btconfig(8) - NetBSD Manual Pages

Command: Section: Arch: Collection:  
BTCONFIG(8)             NetBSD System Manager's Manual             BTCONFIG(8)


NAME
btconfig -- configure bluetooth devices
SYNOPSIS
btconfig [-svz] [device [parameters]] btconfig [-l]
DESCRIPTION
btconfig is used to configure Bluetooth devices. If the device is given, but no parameters, then btconfig will print information about the device. If no device is given, a basic list of devices will be printed. When the -l flag is used, just the device names will be printed.
COMMANDS
The following parameters may be specified with btconfig: up Enable Bluetooth Device. down Disable Bluetooth Device. pscan Enable Page Scan. This enables incoming connections to the device. -pscan Disable Page Scan. iscan Enable Inquiry Scan. This puts the device in Discoverable mode. -iscan Disable Inquiry Scan. encrypt Enable encryption. This will cause the device to request encryption on all baseband connections, and will only work if authentication is also enabled. -encrypt Disable encryption. auth Enable authentication. This will cause the device to request authentication for all baseband connections. -auth Disable authentication. switch Enable Role Switching. In a Bluetooth piconet there is one Master and up to seven Slaves, and normally the device that initiates a connection will take the Master role. Enabling this option allows remote devices to switch connection roles. -switch Disable Role Switching. master Request the Master role when accepting connections. -master Do not request Master role. hold Enable Hold Mode. -hold Disable Hold Mode. sniff Enable Sniff Mode. -sniff Disable Sniff Mode. park Enable Park Mode. -park Disable Park Mode. name name Set human readable name of device. ptype type Set packet types. type is a 16 bit hex value specifying packet types that will be requested by outgoing ACL connec- tions. By default, all packet types that the device sup- ports are enabled, see bluetooth specifications for more information if you want to change this. class class Set class of device. class is a 6 digit hex value the value of which declares the device capabilities. See the "Assigned Numbers - Baseband" document at http://www.bluetooth.com/ for details of constructing a Class of Device value. As a starter, 0x020104 means Desktop Computer, with Networking available. fixed Set fixed pin type. variable Set variable pin type. inquiry Perform device Discovery from the specified device and print details. imode type Set inquiry mode type to control which event formats are generated during a device inquiry. The type can be: std Standard Inquiry Result Event format. rssi Enable Remote Signal Strength Indicator (RSSI) in inquiry results. This will only work if the device features indicate <RSSI with inquiry result>. ext Inquiry Result with RSSI format or Extended Inquiry Result fomat. This will only work where the device features indicate <extended inquiry>, and the Extended Inquiry Result will only occur when the remote device provides the extended information. reset Perform a hard reset on the device and re-initialise system state. voice Set Voice Setting. [This should be 0x0060 for now] pto Set Page Timeout value. This is a decimal value in mil- liseconds, indicating how long the device will attempt to page another device when opening baseband connections. scomtu Change SCO mtu value. This is a decimal value, see ubt(4) for reasons why you may need to do this. All parameters are parsed before any device operations take place. Each time the -v flag is given, verbosity levels will be increased. Super-user privileges are required to change device configurations.
DIAGNOSTICS
Messages indicating the specified device does not exist, the requested address is unknown, or the user is not privileged and tried to alter an device's configuration.
SEE ALSO
bcsp(4), bluetooth(4), bt3c(4), btbc(4), btuart(4), sbt(4), ubt(4)
HISTORY
The btconfig command was written for NetBSD 4.0 by Iain Hibbert under the sponsorship of Itronix, Inc.
BUGS
The output is very messy. NetBSD 9.99 October 11, 2010 NetBSD 9.99
Powered by man-cgi 1.15, Panagiotis Christias
Modified for NetBSD by Kimmo Suominen