- NetBSD Manual Pages
TARGETS(5) NetBSD File Formats Manual TARGETS(5)
Powered by man-cgi (2021-06-01).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
targets -- configuration file for iSCSI targets
The targets file describes the iSCSI storage which is presented to iSCSI
initiators by the iscsi-target(8) service. A description of the iSCSI
protocol can be found in Internet Small Computer Systems Interface RFC
Each line in the file (other than comment lines that begin with a `#')
specifies an extent, a device (made up of extents or other devices), or a
target to present to the initiator.
Each definition, an extent, a device, and a target, is specified on a
single whitespace delimited line.
The extent definition specifies a piece of storage that will be used as
storage, and presented to initiators. It is the basic definition for an
iSCSI target. Each target must contain at least one extent definition.
The first field in the definition is the extent name, which must begin
with the word ``extent'' and be followed by a number. The next field is
the file or NetBSD device which will be used as persistent storage. The
next field is the offset (in bytes) of the start of the extent. This
field is usually 0. The fourth field in the definition is the size of
the extent. The basic unit is bytes, and the shorthand KB, MB, GB, and
TB can be used for kilobytes (1024 bytes), megabytes (1024 kilobytes),
gigabytes (1024 megabytes), and terabytes (1024 gigabytes) respectively.
It is possible to use the word ``size'' to use the full size of the pre-
existing regular file given in the extent name.
The device definition specifies a LUN or device, and is made up of
extents and other devices. It is possible to create hierarchies of
devices using the device definition. The first field in the definition
is the device name, which must begin with the word ``device'' and be fol-
lowed by a number. The next field is the type of resilience that is to
be provided by the device. For simple devices, RAID0 suffices. Greater
resilience can be gained by using the RAID1 resilience field. Following
the resilience field is a list of extents or other devices. Large
devices can be created by using multiple RAID0 extents, in which case
each extent will be concatenated. Resilient devices can be created by
using multiple RAID1 devices or extents, in which case data will be writ-
ten to each of the devices or extents in turn. If RAID1 resilience is
used, all the extents or sub-devices must be the same size. Please note
that RAID1 recovery is not yet supported by the iscsi-target(8) utility.
An extent or sub-device may only be used once.
The target definition specifies an iSCSI target, which is presented to
the iSCSI initiator. Multiple targets can be specified. The first field
in the definition is the target name, which must begin with either of the
words ``target'' or ``lun'' and be followed by a number. Optionally, if
a target is followed by an ``='' sign and some text, the text is taken to
be that of the iSCSI Qualified Name of the target. This IQN is used by
the initiator to connect to the appropriate target. The next field is a
selector for whether the storage should be presented as writable, or
merely as read-only storage. The field of ``rw'' denotes read-write
storage, whilst ``ro'' denotes read-only storage. The next field is the
device or extent name that will be used as persistent storage for this
target. The fourth field is a slash-notation netmask which will be used,
during the discovery phase, to control the network addresses to which
targets will be presented. The magic values ``any'' and ``all'' will
expand to be the same as ``0/0''. If an attempt is made to discover a
target which is not allowed by the netmask, a warning will be issued
using syslog(3) to make administrators aware of this attempt. The admin-
istrator can still use tcp wrapper functionality, as found in
hosts_access(5) and hosts.deny(5) to allow or deny discovery attempts
from initiators as well as using the inbuilt netmask functionality.
/etc/iscsi/targets the list of exported storage targets
syslog(3), hosts.deny(5), hosts_access(5), iscsi-target(8)
The targets file first appeared in NetBSD 4.0.
NetBSD 10.99 December 18, 2007 NetBSD 10.99