- NetBSD Manual Pages
CDPLAY(1) NetBSD General Commands Manual CDPLAY(1)
Powered by man-cgi (2021-06-01).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
cdplay -- compact disc player
cdplay [-a audio device] [-f device] [command ...]
cdplay is a program to control the audio features of a CD-ROM drive.
If no command is given, then cdplay enters interactive mode, reading com-
mands from the standard input.
The following options are available:
-a audio device
Specify the audio device to use. Used only in digital transfer
mode. If not specified, the environment variables AUDIODEV and
SPEAKER will be tried (in this order) to find the device; as a
last resort, /dev/sound will be used. If the ``-a'' command line
option is used, or the CDPLAY_DIGITAL environment variable is
present, digital transfer mode is switched on automatically.
Specify the control device to use. Both absolute paths and paths
relative to /dev are accepted. The suffix `c' (or `d' on some
architectures, see disklabel(8) for details) is added to the
device name if needed. If the device not specified, the environ-
ment variables MUSIC_CD, CD_DRIVE, DISC and CDPLAY will be tried
(in this order) to find the device.
The available commands are listed below. Only as many characters as are
required to uniquely identify a command need be specified. The word play
can be omitted in all cases.
play [first_track [last_track]]
Play from track first_track to track last_track. The first
track has number 1.
play [start_m:start_s.start_f [end_m:end_s.end_f]]
Play from the absolute address (MSF) defined by start_m in
minutes, start_s, in seconds and start_f (frame number) to
the absolute address defined by end_m in minutes, end_s, in
seconds and end_f (frame number). Minutes are in the range
0-99. Seconds are in the range 0-59. Frame numbers are in
the range 0-74.
play [#start_block [length]]
Play starting from the logical block start_block using length
next Skip to the next track.
prev Skip to the previous track.
pause Stop playing. Do not stop the disc.
resume Resume playing. Used after the pause command.
shuffle Select shuffle play. Only valid in interactive mode.
Pick a single track and play it repeatedly. If a track argu-
ment is not given the single command will shut shuffle mode
off and play the disc normally. Only valid in interactive
skip Skip to another track. Only valid when shuffle play is
stop Stop the disc.
eject Eject the disc.
close Inject the disc.
volume left_channel right_channel
Set the volume of left channel to left_channel and the volume
of right channel to right_channel. Allowed values are in the
Set the volume of both left channel right channel to value.
Allowed values are in the range 0-255.
Turn the sound off.
Set the mono mode.
Set the stereo mode.
Play the left subtrack on both left and right channels.
Play the right subtrack on both left and right channels.
info Print the table of contents.
status Display the current audio, media and volume status.
digital n Turn on digital transfer mode. In this mode, cdplay reads
digital data from disc and sends it to an audio device. A
SCSI or ATAPI CD-ROM is required; and the audio device must
support CD audio format (44100 Hz sampling rate, 16-bit
stereo samples). Audio data are read and written in groups
of n frames (5 by default, or 1/15 seconds).
analog Switch from digital back to analog mode.
help Print the list of available commands.
reset Perform the hardware reset of the device.
set msf Set minute-second-frame ioctl mode (default).
set lba Set LBA ioctl mode.
quit Quit the program.
The cdplay command first appeared in NetBSD 1.5. Support for digital
transfer mode was added in NetBSD 4.0.
NetBSD 10.99 January 3, 2012 NetBSD 10.99