ipfstat(8) ipfstat(8)
NAME
ipfstat - reports on packet filter statistics and filter list
SYNOPSIS
ipfstat [ -6aAfghIinosv ] [ -d <device> ] ipfstat -t [ -C ] [ -D <addrport> ] [ -P <protocol> ] [ -S <addrport> ] [ -T <refresh time> ] [ -d <device> ]
DESCRIPTION
ipfstat examines /dev/kmem using the symbols _fr_flags, _frstats, _filterin, and _filterout. To run and work, it needs to be able to read both /dev/kmem and the kernel itself. The kernel name defaults to /netbsd. The default behaviour of ipfstat is to retrieve and dis- play the accumulated statistics which have been accumu- lated over time as the kernel has put packets through the filter.
OPTIONS
-6 Display filter lists for IPv6, if available. -a Display the accounting filter list and show bytes counted against each rule. -A Display packet authentication statistics. -C This option is only valid in combination with -t. Display "closed" states as well in the top. Nor- mally, a TCP connection is not displayed when it reaches the CLOSE_WAIT protocol state. With this option enabled, all state entries are displayed. -d <device> Use a device other than /dev/ipl for interfacing with the kernel. -D <addrport> This option is only valid in combination with -t. Limit the state top display to show only state entries whose destination IP address and port match the addport argument. The addrport specification is of the form ipaddress[,port]. The ipaddress and port should be either numerical or the string "any" (specifying any ip address resp. any port). If the -D option is not specified, it defaults to "-D any,any". -f Show fragment state information (statistics) and held state information (in the kernel) if any is present. 1 ipfstat(8) ipfstat(8) -g Show groups currently configured (both active and inactive). -h Show per-rule the number of times each one scores a "hit". For use in combination with -i. -i Display the filter list used for the input side of the kernel IP processing. -I Swap between retrieving "inactive"/"active" filter list details. For use in combination with -i. -n Show the "rule number" for each rule as it is printed. -o Display the filter list used for the output side of the kernel IP processing. -P <protocol> This option is only valid in combination with -t. Limit the state top display to show only state entries that match a specific protocol. The argu- ment can be a protocol name (as defined in /etc/protocols) or a protocol number. If this option is not specified, state entries for any pro- tocol are specified. -s Show packet/flow state information (statistics only). -sl Show held state information (in the kernel) if any is present (no statistics). -S <addrport> This option is only valid in combination with -t. Limit the state top display to show only state entries whose source IP address and port match the addport argument. The addrport specification is of the form ipaddress[,port]. The ipaddress and port should be either numerical or the string "any" (specifying any ip address resp. any port). If the -S option is not specified, it defaults to "-S any,any". -t Show the state table in a way similar to they way top(1) shows the process table. States can be sorted using a number of different ways. This options requires curses(3) and needs to be compiled in. It may not be available on all operating sys- tems. See below, for more information on the keys that can be used while ipfstat is in top mode. -T <refreshtime> This option is only valid in combination with -t. 2 ipfstat(8) ipfstat(8) Specifies how often the state top display should be updated. The refresh time is the number of seconds between an update. Any postive integer can be used. The default (and minimal update time) is 1. -v Turn verbose mode on. Displays more debugging information.
SYNOPSIS
The role of ipfstat is to display current kernel statis- tics gathered as a result of applying the filters in place (if any) to packets going in and out of the kernel. This is the default operation when no command line parameters are present. When supplied with either -i or -o, it will retrieve and display the appropriate list of filter rules currently installed and in use by the kernel.
STATE TOP
Using the -t option ipfstat will enter the state top mode. In this mode the state table is displayed similar to the way top displays the process table. The -C, -D, -P, -S and -T commandline options can be used to restrict the state entries that will be shown and to specify the frequency of display updates. In state top mode, the following keys can be used to influence the displayed information: d select information to display. l redraw the screen. q quit the program. s switch between different sorting criterion. r reverse the sorting criterion. States can be sorted by protocol number, by number of IP packets, by number of bytes and by time-to-live of the state entry. The default is to sort by the number of bytes. States are sorted in descending order, but you can use the r key to sort them in ascending order.
STATE TOP LIMITATIONS
It is currently not possible to interactively change the source, destination and protocol filters or the refreh frequency. This must be done from the command line. The screen must have at least 80 columns. This is however not checked. 3 ipfstat(8) ipfstat(8) Only the first X-5 entries that match the sort and filter criteria are displayed (where X is the number of rows on the display. There is no way to see more entries. No support for IPv6
FILES
/dev/kmem /dev/ipl /dev/ipstate /netbsd
SEE ALSO
ipf(8)
BUGS
none known. 4
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.