xieperf(1) xieperf(1)
NAME
xieperf - XIE server extension test and demo program
SYNTAX
xieperf [-option ...]
DESCRIPTION
The xieperf program is based upon R5 x11perf(1) , and while not entirely comprehensive in its coverage of the XIE protocol (see BUGS, below), it is intended to be use- ful in the evaluation of XIE implementations in the areas of protocol adherance and performance. The xieperf pro- gram includes tests which execute each of the protocol requests and photoflo elements specified by revision 5.0 of the XIE protocol. In addition, xieperf provides a set of tests which can be used to validate the detection and transmission of XIE protocol request errors, such as Flo- Match, FloValue, and so forth. Finally, xieperf provides a customizable demonstration program for XIE. A test is made up of three components executed in sequence - an initialization function, a test function, and an end function. The initialization function is responsible for allocating and populating test resources, such as pho- tomaps and LUTs, and for creating a stored photoflo which will be executed by the test function. The test function, in most cases, simply executes the stored photoflo for a specified number of repetitions. The end function, which is called following the test function, is used primarily to destroy any non-cachable server resources used by the test, and to free any memory which was dynamically allo- cated by the client. Some tests, such as -modify1, -await, -abort, and -redefine, perform additional steps within the test function inner loop, as required by the element being tested, or in an attempt to make the test more visually appealing. Evaluating the performance of individual XIE elements is not as simple as measuring Core X drawing times. The XIE protocol requires elements to be embedded within photoflos in order to be exercised, and the minimum possible photoflo size is two. This implies that it is impossible to measure performance of a single element in isolation - the time it takes to run the flo depends on what other elements exist in the flo. Extrapolating performance of a single elment (or technique) in a flo must be done care- fully, on a case-by-case basis, since in general measured element performance depends on input image size, data type, and other factors, all of which can be influenced by upstream flo elements. Note further that the number and type of elements in a flo can be influenced by the visuals available on the display, so even flo-flo compar- isons on machines with different visuals must be done with caution. X Version 11 Release 6.3 1 xieperf(1) xieperf(1) Many test labels contain an abbreviated pipeline descrip- tion. For instance. IP/IL/P/ED indicates ImportPhotomap, ImportLUT, Point, and ExportDrawable. Pipelines ending in ED (ExportDrawable) often include hidden elements such as BandExtract, ConvertToIndex, Dither, or Point to match the flo output to the screen visual. Pipelines ending in EP (ExportPhotomap) will result in a blank window. xieperf is compatible with x11perfcomp(1), which is used to compare the outputs of different xieperf and x11perf runs in a nice, tabular format. In xieperf you will need to use the -labels option (see OPTIONS, below), and pro- vide the resulting labels file to x11perfcomp(1) to obtain correct output. See the x11perfcomp(1) man pages for more details on this.
OPTIONS
xieperf accepts the options listed below: -display host:dpy Specifies which display to use. -images <path> Normally, xieperf references image files located in the directory ``images'', which xieperf assumes is located in your current directory. If the ``images'' directory is not in your current directory, or the file has been renamed, use this option to specify its location. -timeout <s> Some tests require the reception of an event such as FloNotify to continue, and may cause xieperf to hang should these events not be received. This option allows the user to specify a timeout value which, if exceeded, will cause xieperf to give up waiting for an event, and continue on with the next test in sequence. Should an event timeout, a warn- ing message will be printed to stderr. The default timeout value is 60 seconds. -sync Runs the tests in synchronous mode. -script <file> Using this option gives the user the ability to run a subset of the available tests and control the number of times the tests are executed on an individual basis. This is thought to be especially useful for those running xieperf for demonstration purposes. Using this option causes xieperf to read commands specified in a script file, or from stdin if <file> is ``-''. Tests are X Version 11 Release 6.3 2 xieperf(1) xieperf(1) specified by newline-terminated input lines of the form "command [-reps n ] [ -repeat m ]". Characters following and including "#" are treated as comments. See the -mkscript option. -repeat <n> Repeats each test n times (by default each test is run 2 times). This option may be used in script files also, in which case the script file -repeat overrides the command line option. -time <s> Specifies how long in seconds each test should be run (default 5 seconds). -depth <depth> Use a visual with <depth> planes per pixel (default is the default visual). -GrayScale Use a GrayScale visual (default is the default visual). -PseudoColor Use a PseudoColor visual (default is the default visual). -StaticGray Use a StaticGray visual (default is the default visual). -StaticColor Use a StaticColor visual (default is the default visual). -TrueColor Use a TrueColor visual (default is the default visual). -DirectColor Use a DirectColor visual (default is the default visual). -WMSafe If xieperf must be run in a window manager environment, use this flag to make xieperf aware of this. If specified, xieperf will create a window, identical to the size of the root window, and all further windows created by xieperf will be transient popup children of this window. If this flag is omitted, xieperf will set the override_redi- rect attribute of all windows to ``True'' and will also do evil things such as calling XInstallColormap. Using this option will cause the window manager to (hopefully) obey window geometry hints specified by xieperf -showtechs Display a comprehensive list of techniques, by category, indicating which of the tech- niques are supported by the XIE server. X Version 11 Release 6.3 3 xieperf(1) xieperf(1) -showlabels Print test label to screen prior to calling any of the test code. This allows the user to know which test is executing in case the test hangs for some reason. -showevents Be verbose when running event and error tests. Also, can be used to catch and dis- play information on any signals received during execution of xieperf that the error events received by xieperf are valid the first time the tests are executed on a new platform. -events Run tests which test for event generation. -errors Run tests which test for error event genera- tion. -loCal Skip test calibration. This may be used when running xieperf in situations where execu- tion timing is not important. Execution times will not be reported by xieperf when this option is enabled. The inner loop repeat count, additionally, is set to a value of 5 (but can be overridden by the -reps option). -all Runs all tests. This may take a while, depending on the speed of your machine, and its floating point capabilities. This option is ignored if a script file is used. -tests Generate a list of the available tests for the xieperf program. In x11perf , this list is normally displayed in the usage state- ment. It was yanked from the usage of xieperf because it was too lengthy. -mkscript Generate a script file suitable for use with the script option. If -repeat or -reps are also specified, they will be automatically placed at the end of each command in the script. The script is generated to stderr. See the -script command, above. -cache <n> Most test flos utilize a photomap resource for a source. A photomap cache of up to n entries is controlled by xieperf to avoid having to constantly reload these images during test initialization. The default cache size is 4. If a value less than the default is specified, the cache size will be set to the default. X Version 11 Release 6.3 4 xieperf(1) xieperf(1) -labels Generates just the descriptive labels for each test specified. Use -all or -range to specify which tests are included. See x11perfcomp(1) for more details. -DIS Pretend we are running xieperf while con- nected to a DIS-only capable implementation of XIE. This will cause xieperf to execute those tests which only use protocol requests found in the DIS subset of XIE, and bypass those which are not DIS compatible. If xieperf detects a DIS server, it will do this automatically, and this option is ignored. Use -all or -range to specify the initial range of tests. -range <test1>[,<test2>] Runs all the tests starting from the speci- fied name test1 until the name test2, including both the specified tests. Some tests, like the event and error tests, also require the -errors or -events options to specified. This option is ignored if a script it used. -reps <n> Fix the inner loop repetitions to n. This indicates how many time the photoflo will be executed each time the test is run. This option is overridden on a per-test basis if specified in a script. Typically, xieperf determines the ideal number of reps during each test's calibration period. -ImportObscuredEvent through -ExportAvailable Test generation of events. Requires -events flag. -BadValue through -FloValueError Test generation of errors. Requires -errors flag. -ColorList Create and destroy Col- orList resource test. -LUT Create and destroy LUT resource test. -Photomap Create and destroy Photomap resource test. -ROI Create and destroy ROI resource test. -Photospace Create and destroy Photospace test. -Photoflo Create and destroy Photoflo test. -QueryPhotomap Query Photomap resource test. X Version 11 Release 6.3 5 xieperf(1) xieperf(1) -QueryColorList Query ColorList resource test. -QueryTechniquesDefault through -QueryTechniquesWhiteAd- just Query techniques as specified by test name. -QueryPhotoflo Query photoflo test. -PurgeColorList PurgeColorList test. -Abort This tests creates a photoflo which is started and blocks for data provided by Put- ClientData(). Instead of sending the data, the test uses XieAbort() to stop the photoflo, and then waits for PhotofloDone event to be send by the server. If the test times out waiting for the event, a error message is sent to stderr. -Await This test creates a flo of the form Import- ClientLUT -> ExportLUT, and starts the flo executing. xieperf then forks, and the child process streams the LUT data to the flo using PutClientData, while the parent blocks in XieAwait. If the flo successfully finishes, XieAwait will return and the flo state, after query, will indicate that it has completed. If XieAwait does not complete naturally, or after return from XieAwait the flo is still active, an error is reported to stderr. Note, on a really slow machine, it is possible that XieAwait will return before the flo has a chance to finish. In this case, use the -timeout option to increase the timeout for this test. -importclientlut1 ImportClientLUT -> ExportLUT test. -importclientphoto1 through -importclientphoto9 Flos of the form ImportClientPhoto -> ExportPhotomap using various decode tech- niques, e.g. G32D, TIFF2, Uncom- pressedTriple, and so forth. -importclientroi1 ImportClientROI with 10 rectangles. -importclientroi2 ImportClientROI with 100 rectangles. X Version 11 Release 6.3 6 xieperf(1) xieperf(1) -encodephoto1 through -encodephoto14 Flos of the form ImportPhotomap -> Export- Photomap using various encode techniques, e.g. G32D, TIFF2, UncompressedTriple, and so forth. Original encoding is shown in left window, image after encoding is shown in right window. -encodeclientphoto1 through -encodeclientphoto11 Two flos, one of the form ImportPhotomap -> ExportClientPhoto, and the other of the form ImportClientPhoto -> ExportPhotomap, where ExportClientPhoto in the first flo uses var- ious encode techniques, e.g. G32D, TIFF2, UncompressedTriple, and so forth. The image before encoding is displayed in the left window, while the right window shows the image which was encoded in the first flo and read back in the second flo. -exportclientlut1 ExportClientLUT test. LUT is displayed in a histogram window. -exportclientroi1 ExportClientROI test, 10 ROIs. The ROIs which are sent to the server are represented by the filled rectangles. The ROIs which are received back from the server by the client are drawn as white bordered non-filled rect- angles. The resulting output illustrates how the server combined the rectangles sent to it. -exportclientroi2 Same as exportclientroi1, except using 100 rectangles. -exportclienthistogram1 through -exportclienthistogram4 ExportClientHistogram tests using various images. The histogram is displayed in a win- dow which overlaps the image. -exportclienthistogramroi1 through -exportclienthistogram- roi4 Same as the ExportClientHistogram test, but using a ROI to identify the area of inter- est. -exportclienthistogramcplane1 through -exportclienthis- togramc- plane4 Same as the ExportClientHistogram test, but using a Control Plane to identify the area of interest. X Version 11 Release 6.3 7 xieperf(1) xieperf(1) -importlut1 Test ImportLUT element, LUT size is 256. -importphoto1 ImportPhotomap -> ExportPhotomap, with source and destination equal. -importphoto2 ImportPhotomap -> ExportDrawable, window destination. -importroi1 ImportROI -> ExportROI, 10 rectangles, source and destination ROIs equal. -importroi2 ImportROI -> ExportROI, 100 rectangles, source and destination ROIs equal. -importdrawable1 ImportDrawable -> ExportDrawable, Source is pixmap, destination is window. -importdrawable2 ImportDrawable -> ExportDrawable, Source and destination is window. -importdrawable3 ImportDrawable -> ExportDrawable, Destina- tion window obscured by source window. -importdrawable4 ImportDrawable -> ExportDrawable, Source window obscured by destination window. -importdrawable5 ImportDrawablePlane -> ExportDrawablePlane, pixmap, source = destination. -importdrawable6 ImportDrawablePlane -> ExportDrawablePlane, window, source = destination. -importdrawable7 ImportDrawablePlane -> ExportDrawablePlane, window, source obscures destination. -importdrawable8 ImportDrawablePlane -> ExportDrawablePlane, window, destination obscures source. -constrain1 Constrain HardClip technique test, drawable destination. -constrain2 Constrain ClipScale technique test, drawable destination. -constrainphoto1 Constrain HardClip technique test, photomap X Version 11 Release 6.3 8 xieperf(1) xieperf(1) destination. -constrainphoto2 Constrain ClipScale technique test, photomap destination. -convolve1 Boxcar 3x3 convolution test. Smoothing or lowpass filter. -convolve2 Boxcar 5x5 convolution test. Smoothing or lowpass filter. -convolve3 LaPlacian 3x3 convolution test. Edge or highpass filter. -convolve4 LaPlacian 5x5 convolution test. Edge or highpass filter. -convolveroi1 LaPlacian 3x3 convolution test, with ROI. -convolveroi2 LaPlacian 5x5 convolution test, with ROI. -convolvecplane1 LaPlacian 3x3 convolution test, with Control Plane. -convolvecplane2 LaPlacian 5x5 convolution test, with Control Plane. -math1 through -mathcplane7 Various tests which exercise the Math ele- ment, some tests using ROIs and control planes. -arithmeticdyadic1 through -arithmeticdyadic5 Arithmetic element tests, using photomaps as the operands. -arithmeticmonadic1 through -arithmeticmonadic9 Arithmetic element tests, photomap and con- stant operands. -arithmeticdyadicroi1 through -arithmeticdyadicroi5 Arithmetic element tests, using photomaps as the operands, with ROIs. -arithmeticmonadicroi1 through -arithmeticmonadicroi9 Arithmetic element tests, photomap and con- stant operands, with ROIs. -arithmeticdyadiccplane1 through -arithmeticdyadiccplane5 Arithmetic element tests, using photomaps as the operands, with Control Planes. X Version 11 Release 6.3 9 xieperf(1) xieperf(1) -arithmeticmonadiccplane1 through -arithmeticmonadicc- plane9 Arithmetic element tests, photomap and con- stant operands, with Control Planes. -arithmeticfloatdyadic1 though -arithmeticfloatdyadic5 Arithmetic element tests, using photomaps as the operands, unconstrained. -arithmeticfloatmonadic1 though -arithmeticfloatmonadic9 Arithmetic element tests, photomap and con- stant operands, unconstrained. -arithmeticroifloatdyadic1 to -arithmeticroifloatdyadic5 Arithmetic element tests, photomaps as the operands, ROIs, unconstrained. -arithmeticroifloatmonadic1 to -...rithmeticroifloat- monadic9 Arithmetic element tests, photomap and con- stant operands, ROIs, unconstrained. -band1 BandSelect element test. Image input is triple band. If visual of xieperf window is a color visual, then three BandSelect ele- ments are used to extract the indivudual bands, they are combined once again using BandCombine, and displayed using Convert- ToIndex. If the visual is not color, e.g. GrayScale or StaticGray, then the flo simply uses one BandSelect element to extract a single band for display. -band2 BandCombine test. Input bands are made of of three separate single band photomaps. These are combined using a BandCombine element, which is followed by a BandExtract and ExportDrawable. CCIR 601-1 coefficients. -band3 BandExtract test. Input is a triple band photomap. CCIR 601-1 coefficients. Destina- tion window colormap is gray ramp. -band4 BandExtract test. Input is a triple band photomap. CCIR 601-1 coefficients. Destina- tion window colormap is RGB_BEST_MAP stan- dard colormap. -band5 BandExtract test. Input is a triple band photomap. CCIR 601-1 coefficients. Destina- tion window colormap is RGB_DEFAULT_MAP standard colormap. X Version 11 Release 6.3 10 xieperf(1) xieperf(1) -comparedyadic1 through -comparedyadic6 Test various Compare operators with dyadic photomap operands. -comparemonadic1 through -comparemonadic6 Test various compare operators with pho- tomap, constant operands. -compareroidyadic1 through -compareroidyadic6 Test various Compare operators with dyadic photomap operands, using ROIs. -compareroimonadic1 through -compareroimonadic6 Test various compare operators with pho- tomap, constant operands, using ROIs. -comparecplanedyadic1 through -comparecplanedyadic6 Test various Compare operators with dyadic photomap operands, Control Planes. -comparecplanemonadic1 through -comparecplanemonadic6 Test various compare operators with pho- tomap, constant operands, Control Planes. -matchhistogram1 through -matchhistogram18 MatchHistogram element tests, using various images and histogram matching techniques. -matchhistogramroi1 through -matchhistogramroi6 A selection of MatchHistogram element tests, with ROIs. -matchhistogramcplane1 through -matchhistogramcplane6 A selection of MatchHistogram element tests, with Control Planes. -unconstrain1 ImportPhotomap, Unconstrain, Constrain(Clip- Scale), ExportDrawable test. -pasteup1 through -pasteup2 PasteUp element tests. -geometry1 through -geometry14 Geometry element tests, including rotations, scales, and mirroring. NearestNeighbor technique. -geometry15 through -geometry28 Geometry element tests, including rotations, scales, and mirroring. AntiAlias technique. -geometry29 through -geometry42 Geometry element tests, including rotations, scales, and mirroring. X Version 11 Release 6.3 11 xieperf(1) xieperf(1) BilinearInterpolation technique. -geomg31dscale1 through -geometryfaxradio1 Tests to exercise the various FAX decoders and the Geometry element. -dither1 Dither test, ErrorDiffusion dither tech- nique, ExportDrawable. -dither2 Dither test, ErrorDiffusion dither tech- nique, ExportDrawablePlane. -dither3 Dither test, Ordered(4) dither technique, ExportDrawable. -dither4 Dither test, Ordered(4) dither technique, ExportDrawablePlane. -dither5 Dither test, Ordered(8) dither technique, ExportDrawable. -dither6 Dither test, Ordered(8) dither technique, ExportDrawablePlane. -dither7 Dither test, Default dither technique, ExportDrawable. -dither8 Dither test, Default dither technique, ExportDrawablePlane. -logicalmonadic1 through -logicalmonadic16 Logical element, photomap and a constant of 0 as operands, various operators. -logicaldyadic1 through -logicaldyadic16 Logical element tests, dyadic photomaps as operands, various operators. -logicalmonadicroi1 through -logicalmonadicroi16 Logical element, photomap and constant of 0 operands, various operators, ROIs. -logicaldyadicroi1 through -logicaldyadicroi16 Logical element, dyadic photomaps as operands, various operators, ROIs. -logicalmonadiccplane1 through -logicalmonadiccplane16 Logical element, photomap and constant of 0 operands, various operators, Control Planes. -logicaldyadiccplane1 through -logicaldyadiccplane16 Logical element, dyadic photomaps as operands, various operators, Control Planes. X Version 11 Release 6.3 12 xieperf(1) xieperf(1) -blend1 Blend element test. Monadic source, 0.1 source constant. Alpha constant of 0.5. -blend2 Blend element test. Dyadic sources. Alpha constant of 0.5. -blendroi1 Blend test. Monadic source, 0.1 source con- stant. Alpha constant of 0.5. ROIs. -blendroi2 Blend element test. Dyadic sources. Alpha constant of 0.5. Uses ROIs. -blendcplane1 Blend test. Monadic source, 0.1 source con- stant. Alpha constant of 0.5. Control Plane. -blendcplane2 Blend element test. Dyadic sources. Alpha constant of 0.5. Control Plane. -blendalpha1 Blend test. Monadic source, 220 source con- stant. Alpha plane is a photomap. -blendalpha2 Blend test. Dyadic sources. Alpha plane is a constant 220. -blendalpharoi1 Blend test. Monadic source, 220 source con- stant. Alpha plane photomap. ROIs. -blendalpharoi2 Blend test. Dyadic sources. Alpha plane is a constant 220. ROIs. -triplepoint1 through -triplepoint2 Illustrate use of point and Standard col- ormaps for rendering triple band images. -funnyencode1 through -funnyencode8 These tests are design to perform limited exercising of XIE's capability of dealing with various encodings of flo source data. The test init function obtains a photomap using ICP -> EP. A series of independent permanent flo pairs, one of the form IP -> EP, and the other of the basic form IP -> ED, are constructed. The encoding parameters for the ExportPhotomap (EP) element in the first flo are derived from test configura- tion. The number of flo pairs created is also dependent upon test configuration. The tests can be configured so that the test init function will constrain the input pho- tomap to a specified number of levels, on a per-band basis, so that word-sized and quad- sized pixels are passed through the flos. X Version 11 Release 6.3 13 xieperf(1) xieperf(1) Some tests below take advantage of this. See tests.c for test configuration, and hints on how to add similar tests. -point1 through -point3 Simple Point element tests. Drawable desti- nation. -pointroi1 Simple Point element test which uses ROIs. Drawable destination. -pointcplane1 Simple Point element test which uses a Con- trol Plane. Drawable destination. -pointphoto1 Simple Point element test. Photomap destina- tion. -pointroiphoto1 Simple Point element test which uses a ROIs. Photomap destination. -pointcplanephoto1 Simple Point element test which uses a Con- trol Plane. Photomap destination. -redefine Two flographs are created which are the same in structure, expect for the x and y offsets specified for the ExportDrawable flo ele- ments. The test init function creates a photoflo based upon one of the two flo- graphs. The inner loop of the test function uses XieRedefinePhotoflo() to alternate between each of the flographs. Make sure that your ineer loop reps are 2 or greater in order to exercise this test fully (see -reps). -modify1 Test XieModifyPhotoflo() by adjust ROI off- sets and size. -modify2 Test XieModifyPhotoflo() by changing the LUT input to a Point element. -modify3 Test XieModifyPhotoflo() by changing Export- Drawable x and y offsets. -modify4 This test creates a rather long flo of arithmetic elements, each which does nothing more than add 1 to a small image. The test init function scales the input photomap. The ExportDrawable x and y offset is modified randomly during each iteration of the test function inner loop. -modify5 This test creates a rather long flo of arithmetic elements, each which does nothing X Version 11 Release 6.3 14 xieperf(1) xieperf(1) more than add 1 to a large image. Each rep, the Geometry and ExportDrawable elements at the end of the flo are modifed to crop a small piece of the input into its appropri- ate place in the larger image. -rgb1 through -rgb16 These tests all basically take an Uncom- pressedTriple image as input, send it to ConvertFromRGB which converts the image to some configured colorspace, and then send the converted image on to ConvertToRGB prior to display. The original image is displayed in the lefthand window, and the image which has passed through the flo is shown in the righthand window. The goal of these test is to show that ConvertFromRGB -> ConvertToRGB is lossless. -converttoindexpixel ConvertToIndex test, TripleBand BandByPixel. -converttoindexplane ConvertToIndex test, TripleBand BandByPlane. -convertfromindex The test init function uses a flo containing ConvertToIndex to display an image in the left window. The test function uses this drawable as input to a flo which does Con- vertFromIndex -> ConvertToIndex and sends the resulting image to the right window. The result should be lossless. -complex A somewhat large flo which uses control planes, LUTs, Point, PasteUp, Logical, Con- strain, Dither, Geometry, MatchHistogram, BandCombine, and BandSelect elements. See the Postscript file ''complex.ps'' for a rendition of the photoflo which is executed.
X DEFAULTS
There are no X defaults used by this program.
SEE ALSO
X(1), x11perf(1), x11perfcomp(1)
BUGS
There should be a IMAGES environment variable to augment the -images option. Many tests only scratch the surface of possible test cases. Some of the options available for certain flo ele- ments are either inadequately tested, or ignored X Version 11 Release 6.3 15 xieperf(1) xieperf(1) altogether. There are insufficent tests for bitonal, large pixel, or triple band tests. Some of the test names are inconsistently cased, e.g. -Abort and -dither1. Some tests are hopelessly slow when run against machines with slow FPUs. Bitonal images are for the most part displayed using the ExportDrawable flo element, however, ExportDrawablePlane would be a better choice.
AUTHOR
Syd Logan, AGE Logic, Inc. X Version 11 Release 6.3 16
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.