bge(4) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
BGE(4)                  NetBSD Kernel Interfaces Manual                 BGE(4)


NAME

     bge -- Broadcom BCM57xx/BCM590x 10/100/Gigabit Ethernet driver


SYNOPSIS

     bge* at pci? dev ? function ?

     Configuration of PHYs may also be necessary.  See mii(4).


DESCRIPTION

     The bge driver provides support for various NICs based on the Broadcom
     BCM570x, 571x, 572x, 575x, 576x, 578x, 5776x and 5778x Gigabit Ethernet
     controller chips and the 590x and 5779x Fast Ethernet controller chips,
     including the following:

     ·   3Com 3c996-T (10/100/1000baseT)
     ·   3Com 3c996-SX (1000baseSX)
     ·   3Com 3c996B-T (10/100/1000baseT)
     ·   Allied-Telesis AT-2972LX10/LC
     ·   Apple Thunderbolt to Gigabit Ethernet adapter A1433
         (10/100/1000baseT)
     ·   Dell PowerEdge 1750 integrated BCM5704C NIC (10/100/1000baseT)
     ·   Dell PowerEdge 2550 integrated BCM5700 NIC (10/100/1000baseT)
     ·   Dell PowerEdge 2650 integrated BCM5703 NIC (10/100/1000baseT)
     ·   Fujitsu PRIMEPOWER 250/450 LAN (10/100/1000baseT)
     ·   Fujitsu PW0G8GE1U (1000baseSX)
     ·   Fujitsu PW0G8GE2U (10/100/1000baseT)
     ·   Fujitsu PW008GE4 (1000baseSX)
     ·   Fujitsu PW008GE5 (10/100/1000baseT)
     ·   Fujitsu PW008QG1U (10/100/1000baseT)
     ·   HP ProLiant NC320T PCI-E Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC320m PCI-E Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC331T PCI-E Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC332T PCI-E Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC370F PCI-X Gigabit NIC (1000baseSX)
     ·   HP ProLiant NC370T PCI-X Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC1020 PCI Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC6770 PCI-X Gigabit NIC (1000baseSX)
     ·   HP ProLiant NC7760 embedded PCI Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC7770 PCI-X Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC7771 PCI-X Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC7780 embedded PCI-X Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC7781 embedded PCI-X Gigabit NIC (10/100/1000baseT)
     ·   HP ProLiant NC7782 embedded PCI-X Gigabit NIC (10/100/1000baseT)
     ·   IBM ThinkPad T43/T43p integrated BCM5751M NIC (10/100/1000baseT)
     ·   IBM xSeries 235 integrated BCM5703X NIC (10/100/1000baseT)
     ·   IBM xSeries 305 integrated BCM5703X NIC (10/100/1000baseT)
     ·   Netgear GA302T (10/100/1000baseT)
     ·   SysKonnect SK-9D21 (10/100/1000baseT)
     ·   SysKonnect SK-9D41 (1000baseSX)

     The bge driver supports IPv4 IP, TCP, and UDP checksum offload for
     receive, IP checksum offload for transmit, VLAN tag insertion and strip-
     ping, as well as a 256-bit multicast hash filter.  The BCM5717, BCM5718,
     BCM5723, BCM5754, BCM5755, BCM5761, BCM5762, BCM5764, BCM5784, BCM5785,
     BCM5787 and BCM577xx chips also support IPv6 receive TCP/UDP checksum
     offload.  The bge driver supports this feature of the chip.  See
     ifconfig(8) for information on how to enable this feature.

     The BCM5700, BCM5701, BCM5702, BCM5703, BCM5704, BCM5714, BCM5717,
     BCM5719, BCM5720, BCM5762, BCM5780, BCM57765 and BCM57766 also support
     jumbo frames, which can be configured via the interface MTU setting.
     Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility con-
     figures the adapter to receive and transmit Jumbo frames.

     The level of interrupt mitigation for received packets can be adjusted
     with the hw.bge.rx_lvl sysctl(8) control.  A value of 1 yields a bge
     interrupt for every two full-sized Ethernet frames.  Each increment of
     the value will, roughly, halve receive interrupt rate, up to a maximum of
     5, which interrupts about every 30 to 40 full-sized TCP segments.

     The bge driver supports the following media types:

     autoselect  Enable autoselection of the media type and options.  The user
                 can manually override the autoselected mode by adding media
                 options to the appropriate ifconfig.if(5) file.

     10baseT     Set 10Mbps operation.  The ifconfig(8) mediaopt option can
                 also be used to select either full-duplex or half-duplex
                 modes.

     100baseTX   Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8)
                 mediaopt option can also be used to select either full-duplex
                 or half-duplex modes.

     1000baseT   Set 1000baseT operation over twisted pair.  Both full-duplex
                 and half-duplex modes are supported.

     1000baseSX  Set 1000Mbps (Gigabit Ethernet) operation.  Both full-duplex
                 and half-duplex modes are supported.

     The bge driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).


DIAGNOSTICS

     bge%d: can't find mem space  A fatal initialization error has occurred.

     bge%d: couldn't map interrupt  A fatal initialization error has occurred.

     bge%d: watchdog timeout -- resetting  The device has stopped responding
     to the network, or there is a problem with the network connection
     (cable).


SEE ALSO

     arp(4), brgphy(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)


HISTORY

     The bge driver first appeared in NetBSD 1.6.1.


AUTHORS

     The bge driver was written by Bill Paul <wpaul@windriver.com> for FreeBSD
     and ported to NetBSD by Frank van der Linden <fvdl@wasabisystems.com>,
     Jason R. Thorpe <thorpej@wasabisystems.com> and Jonathan Stone
     <jonathan@dsg.stanford.edu>.

NetBSD 10.99                   October 15, 2019                   NetBSD 10.99