- NetBSD Manual Pages
ADB(4) NetBSD Kernel Interfaces Manual ADB(4)
Powered by man-cgi (2021-06-01).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
adb -- Apple Desktop Bus driver
adb* at obio?
The Apple Desktop Bus (ADB) is the single-master, multiple-slave, low-
speed serial bus interface used by Macintosh computers to connect input
devices such as keyboards, mice, trackpads, trackballs, and graphics
tablets to the machine. NetBSD provides support for the Apple Desktop
Bus as found on all supported mac68k models, as well as macppc models
with on-board ADB (PowerBooks and ``Old World'' models).
The adb driver accesses the ADB controller using the so-called
``HWDIRECT'' method. This method of access bypasses the Macintosh ROM
and uses only NetBSD routines for ADB access. This is the only method
supported on macppc and is the default for mac68k systems.
On mac68k systems there is an alternate method of accessing the ADB con-
troller. With the Macintosh ROM Glue (MRG) method, the routines written
for MacOS are used. To enable this method of ADB access, uncomment the
in your kernel configuration file.
The ioctl(2) call is used to control the ADB event device. The following
is a list of available ioctl(2) commands:
ADBIOC_DEVSINFO Get ADB Device Info
The adb event device will return an array of informa-
tion containing an entry for each device connected to
the bus. Each entry contains the current address,
default address, and handler ID for the corresponding
ADBIOC_GETREPEAT Get Keyboard Repeat Info
Returns a structure containing the current keyboard
repeat delay and keyboard repeat interval.
ADBIOC_SETREPEAT Set Keyboard Repeat Rate
Sets the keyboard repeat delay and interval to the val-
ues specified by argp.
ADBIOC_RESET ADB Reset
Perform a reset of the ADB which will reinitialize all
of the devices attached to the bus.
ADBIOC_LISTENCMD ADB Listen Command
Send data to the register of the ADB device specified
by argp. This command is not fully implemented at this
NetBSD includes support for the following ADB devices, sorted by driver
abtn ADB mouse button?
aed ADB event device
akbd ADB keyboard
ams ADB mouse
apm APM emulation
/dev/adb The ADB event device.
aed0 at adb0 addr 0: ADB Event device This is a normal autoconfiguration
message noting the presence of the adb event device.
adb0 at obio0 offset 0x16000 irq 18: 2 targets A standard autoconfigura-
tion message indicating the initialization of the ADB subsystem.
adb: no devices found. No ADB devices were found to be connected to the
bus during autoconfiguration.
adb: using %s series hardware support. Indicates the class of ADB hard-
ware support the machine uses.
adb: hardware type unknown for this machine. The ADB hardware in this
machine is currently unsupported.
adb: no ROM ADB driver in this kernel for this machine. The kernel lacks
the necessary Macintosh ROM Glue (MRG) support for accessing the ADB
hardware on this machine.
adb: using serial console. A serial console will be used for user input
rather than the ADB event device.
adb: %s at %d. An ADB device of the type specified by %s has been found
at location %d.
aed(4), akbd(4), ams(4), apm(4)
The adb interface first appeared in NetBSD 0.9. It has been under devel-
opment ever since.
Bradley A. Grantham wrote the original adb driver, including the MRG sup-
port. The hardware direct interface was written by John P. Wittkowski.
The PowerManager interface was written by Takashi Hamada.
· Not every class of ADB hardware is supported yet.
· The talk command is currently unimplemented.
· The listen command is not implemented yet.
· Not all multi-button mice are currently supported.
· Only mapped and relative-position ADB devices (i.e. keyboards and
mice) are supported. Thus absolute-position and other exotic devices
will not work.
· Some of the diagnostic messages in this man page need to be updated.
Some mac68k machines contain so-called dirty ROM. These machines are
the: Mac SE/30, Mac II, Mac IIx, and Mac IIcx. Machines with dirty ROM
may experience trouble booting if the MRG code is used, especially under
the following conditions:
· Both a keyboard and a mouse are not attached to the computer.
· An extended keyboard is attached to the computer.
On (some) machines with dirty ROM, the ROM indicates the presence of a
``ghost'' keyboard or mouse. When this nonexistent device is probed for,
the result is an infinite loop. This is believed to be triggered by the
adb driver probing for extended mice, and non-EMP Logitech mice.
NetBSD 9.2 August 31, 2018 NetBSD 9.2