inetd(8) - NetBSD Manual Pages

Command: Section: Arch: Collection:  
INETD(8)                NetBSD System Manager's Manual                INETD(8)

inetd, inetd.conf -- internet ``super-server''
inetd [-d] [-l] [configuration file]
inetd should be run at boot time by /etc/rc (see rc(8)). It then opens sockets according to its configuration and listens for connections. When a connection is found on one of its sockets, it decides what service the socket corresponds to, and invokes a program to service the request. After the program is finished, it continues to listen on the socket (except in some cases which will be described below). Essentially, inetd allows running one daemon to invoke several others, reducing load on the system. The options available for inetd: -d Turns on debugging. -l Turns on libwrap connection logging. Upon execution, inetd reads its configuration information from a configu- ration file which, by default, is /etc/inetd.conf. The path given for this configuration file must be absolute, unless the -d option is also given on the command line. There must be an entry for each field of the configuration file, with entries for each field separated by a tab or a space. Comments are denoted by a ``#'' at the beginning of a line. There must be an entry for each field (except for one special case, described below). The fields of the configuration file are as follows: [listen-addr:]service-spec socket-type[:accept-filter] protocol[,sndbuf=size][,rcvbuf=size] wait/nowait[:max] user[:group] server-program server program arguments The listen-addr specifies the local address inetd should use when listen- ing. The single character ``*'' means INADDR_ANY: all local addresses. To avoid the need to repeat listen addresses over and over again, listen addresses are inherited from line to line, and the listen address can be changed without defining a service by including a line containing just a listen-addr followed by a colon. The default (compatible with historical configuration files) is *. To return to this behavior after configuring some services with specific listen addresses, give * explicitly. Note that restricted listen addresses are meaningless and ignored for UNIX-domain services, and are not supported for Sun-RPC services. All Sun-RPC services always listen on all interfaces. The form of the service-spec varies with the service type. For Internet services, the service-spec can be either the name of a service from /etc/services or a decimal port number. For ``internal'' services (dis- cussed below), the service name must be the official name of the service (that is, the first entry in /etc/services) and not an alias for it. For Sun-RPC based services, the service-spec has the form service-name/version. The service name must be a valid RPC service name from the file /etc/rpc. The version on the right of the ``/'' is the RPC version number. This can simply be a single numeric argument or a range of versions. A range is bounded by the low version to the high version - e.g. ``rusers/1-3''. For UNIX-domain (local) services, the service-spec is the path name to listen on. The socket-type should be one of ``stream'', ``dgram'', ``raw'', ``rdm'', or ``seqpacket'', depending on whether the socket is a stream, datagram, raw, reliably delivered message, or sequenced packet socket. Optionally, for Internet services, an accept filter (see accept_filter(9)) can be specified by appending a colon to socket-type, followed by the name of the desired accept filter. In this case inetd will not see new connections for the specified service until the accept filter decides they are ready to be handled. The protocol must be a valid protocol as given in /etc/protocols or (for UNIX-domain services) the string ``unix''. The most common are ``tcp'' and ``udp''. For TCP and UDP, the IP version (4 or 6) may be specified explicitly by appending 4 or 6 to the protocol name. Otherwise the default version (IPv4) is used. For Sun-RPC the string ``rpc'' and a slash should be prepended: ``rpc/tcp'' or ``rpc/udp''. If you would like to enable special support for faithd(8), prepend the string ``faith'' and a slash: ``faith/tcp6''. In addition to the protocol, the configuration file may specify the send and receive socket buffer sizes for the listening socket. This is espe- cially useful for TCP: the window scale factor, which is based on the receive socket buffer size, is advertised when the connection handshake occurs and thus the socket buffer size must be set on the listen socket. By increasing the socket buffer sizes, better TCP performance may be realized in some situations. The socket buffer sizes are specified by appending their values to the protocol specification as follows: tcp,rcvbuf=16384 tcp,sndbuf=64k tcp,rcvbuf=64k,sndbuf=1m A literal value may be specified, or modified using `k' to indicate kilo- bytes or `m' to indicate megabytes. Socket buffer sizes may be specified for all services and protocols except for tcpmux services. The wait/nowait entry is used to tell inetd if it should wait for the server program to return, or continue processing connections on the socket. If a datagram server connects to its peer, freeing the socket so inetd can receive further messages on the socket, it is said to be a ``multi-threaded'' server, and should use the ``nowait'' entry. For datagram servers which process all incoming datagrams on a socket and eventually time out, the server is said to be ``single-threaded'' and should use a ``wait'' entry. comsat(8) (biff(1)) and ntalkd(8) are both examples of the latter type of datagram server. tftpd(8) is an excep- tion; it is a datagram server that establishes pseudo-connections. It must be listed as ``wait'' in order to avoid a race; the server reads the first packet, creates a new socket, and then forks and exits to allow inetd to check for new service requests to spawn new servers. The optional ``max'' suffix (separated from ``wait'' or ``nowait'' by a dot or a colon) specifies the maximum number of server instances that may be spawned from inetd within an interval of 60 seconds. When omitted, ``max'' defaults to 40. If it reaches this maximum spawn rate, inetd will log the problem (via the syslogger using the LOG_DAEMON facility and LOG_ERR level) and stop handling the specific service for ten minutes. Stream servers are usually marked as ``nowait'' but if a single server process is to handle multiple connections, it may be marked as ``wait''. The master socket will then be passed as fd 0 to the server, which will then need to accept the incoming connection. The server should eventu- ally time out and exit when no more connections are active. inetd will continue to listen on the master socket for connections, so the server should not close it when it exits. identd(8) is usually the only stream server marked as wait. The user entry should contain the user name of the user as whom the server should run. This allows for servers to be given less permission than root. Optionally, a group can be specified by appending a colon to the user name, followed by the group name (it is possible to use a dot (``.'') in lieu of a colon, however this feature is provided only for backward compatibility). This allows for servers to run with a different (primary) group id than specified in the password file. If a group is specified and user is not root, the supplementary groups associated with that user will still be set. The server-program entry should contain the pathname of the program which is to be executed by inetd when a request is found on its socket. If inetd provides this service internally, this entry should be ``internal''. The server program arguments should be just as arguments normally are, starting with argv[0], which is the name of the program. If the service is provided internally, the word ``internal'' should take the place of this entry. It is possible to quote an argument using either single or double quotes. This allows you to have, e.g., spaces in paths and param- eters. Internal Services inetd provides several "trivial" services internally by use of routines within itself. These services are "echo", "discard", "chargen" (charac- ter generator), "daytime" (human readable time), and "time" (machine readable time, in the form of the number of seconds since midnight, Jan- uary 1, 1900 GMT). For details of these services, consult the appropri- ate RFC. TCP services without official port numbers can be handled with the RFC1078-based tcpmux internal service. TCPmux listens on port 1 for requests. When a connection is made from a foreign host, the service name requested is passed to TCPmux, which performs a lookup in the ser- vice name table provided by /etc/inetd.conf and returns the proper entry for the service. TCPmux returns a negative reply if the service doesn't exist, otherwise the invoked server is expected to return the positive reply if the service type in /etc/inetd.conf file has the prefix "tcpmux/". If the service type has the prefix "tcpmux/+", TCPmux will return the positive reply for the process; this is for compatibility with older server code, and also allows you to invoke programs that use stdin/stdout without putting any special server code in them. Services that use TCPmux are "nowait" because they do not have a well-known port number and hence cannot listen for new requests. inetd rereads its configuration file when it receives a hangup signal, SIGHUP. Services may be added, deleted or modified when the configura- tion file is reread. inetd creates a file /var/run/ that con- tains its process identifier. libwrap Support for TCP wrappers is included with inetd to provide internal tcpd- like access control functionality. An external tcpd program is not needed. You do not need to change the /etc/inetd.conf server-program entry to enable this capability. inetd uses /etc/hosts.allow and /etc/hosts.deny for access control facility configurations, as described in hosts_access(5). Nota Bene: TCP wrappers do not affect/restrict UDP or internal services. IPsec The implementation includes a tiny hack to support IPsec policy settings for each socket. A special form of the comment line, starting with ``#@'', is used as a policy specifier. The content of the above comment line will be treated as a IPsec policy string, as described in ipsec_set_policy(3). Multiple IPsec policy strings may be specified by using a semicolon as a separator. If conflicting policy strings are found in a single line, the last string will take effect. A #@ line affects all of the following lines in /etc/inetd.conf, so you may want to reset the IPsec policy by using a comment line containing only #@ (with no policy string). If an invalid IPsec policy string appears in /etc/inetd.conf, inetd logs an error message using syslog(3) and terminates itself. IPv6 TCP/UDP behavior If you wish to run a server for both IPv4 and IPv6 traffic, you will need to run two separate processes for the same server program, specified as two separate lines in /etc/inetd.conf using ``tcp4'' and ``tcp6'' respec- tively. Plain ``tcp'' means TCP on top of the current default IP ver- sion, which is, at this moment, IPv4. Under various combination of IPv4/v6 daemon settings, inetd will behave as follows: If you have only one server on ``tcp4'', IPv4 traffic will be routed to the server. IPv6 traffic will not be accepted. If you have two servers on ``tcp4'' and ``tcp6'', IPv4 traffic will be routed to the server on ``tcp4'', and IPv6 traffic will go to server on ``tcp6''. If you have only one server on ``tcp6'', only IPv6 traffic will be routed to the server. The kernel may route to the server IPv4 traf- fic as well, under certain configuration. See ip6(4) for details.
/etc/inetd.conf configuration file for all inetd provided services /etc/services service name to protocol and port number mappings. /etc/protocols protocol name to protocol number mappings /etc/rpc Sun-RPC service name to service number mappings. /etc/hosts.allow explicit remote host access list. /etc/hosts.deny explicit remote host denial of service list.
hosts_access(5), hosts_options(5), protocols(5), rpc(5), services(5), comsat(8), fingerd(8), ftpd(8), rexecd(8), rlogind(8), rshd(8), telnetd(8), tftpd(8) J. Postel, Echo Protocol, RFC, 862, May 1983. J. Postel, Discard Protocol, RFC, 863, May 1983. J. Postel, Character Generator Protocol, RFC, 864, May 1983. J. Postel, Daytime Protocol, RFC, 867, May 1983. J. Postel and K. Harrenstien, Time Protocol, RFC, 868, May 1983. M. Lottor, TCP port service Multiplexer (TCPMUX), RFC, 1078, November 1988.
The inetd command appeared in 4.3BSD. Support for Sun-RPC based services is modeled after that provided by SunOS 4.1. Support for specifying the socket buffer sizes was added in NetBSD 1.4. In November 1996, libwrap support was added to provide internal tcpd-like access control function- ality; libwrap is based on Wietse Venema's tcp_wrappers. IPv6 support and IPsec hack was made by KAME project, in 1999.
Host address specifiers, while they make conceptual sense for RPC ser- vices, do not work entirely correctly. This is largely because the portmapper interface does not provide a way to register different ports for the same service on different local addresses. Provided you never have more than one entry for a given RPC service, everything should work correctly (Note that default host address specifiers do apply to RPC lines with no explicit specifier.) ``tcpmux'' on IPv6 is not tested enough.
Enabling the ``echo'', ``discard'', and ``chargen'' built-in trivial ser- vices is not recommended because remote users may abuse these to cause a denial of network service to or from the local host. NetBSD 9.0 July 19, 2017 NetBSD 9.0
Powered by man-cgi (2024-03-20). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.