scsictl(8) - NetBSD Manual Pages

SCSICTL(8)              NetBSD System Manager's Manual              SCSICTL(8)


NAME
scsictl -- a program to manipulate SCSI devices and busses
SYNOPSIS
scsictl device command [arg [...]]
DESCRIPTION
scsictl allows a user or system administrator to issue commands to and otherwise control SCSI devices and busses. It is used by specifying a device or bus to manipulate, the command to perform, and any arguments the command may require. scsictl determines if the specified device is an actual device or a SCSI bus automatically, and selects the appropriate command set. For commands which scsictl issues a SCSI command to the device directly, any returned sense information will be decoded by scsictl and displayed to the standard output.
DEVICE COMMANDS
The following commands are supported for SCSI devices: debug level Set the debugging level for the given device; the following flags are supported: 1 Show scsi commands, errors, data. 2 Routine flow tracking. 4 Internal info from routine flows. 8 Device specific debugging. This option is only supported with kernels compiled with SCSIPI_DEBUG. defects [primary] [grown] [block|byte|physical] Read the primary and/or grown defect lists from the speci- fied device in block, byte from index, or physical sector format. The default is to return both the primary and grown defect lists in physical sector format. This command is only supported on direct access devices. format [blocksize [immediate]] (Low level) format the named device. If the optional blocksize parameter is provided, the device geometry will be modified to use the specified blocksize. If this param- eter is different form the Current or Default Mode Page 3 parameters, the device will update Mode Page 3 at the suc- cessful completion of the Format. Device geometry may change as a result of using a new device blocksize. When the optional blocksize parameter is specified, the Defect List on the drive will revert to the original primary defect list created at the time of manufacture if avail- able. The drive will usually recertify itself during the Format and add any other defective blocks to the new Defect List. Some disks may not support the ability to change the blocksize and may enter a Degraded Mode when fed a Format command of this type. If this happens the standard recov- ery for the drive requires issuing a correct Format com- mand, i.e. one without the blocksize parameter. When the immediate parameter is also specified, the disk is instructed to return from the format command right away. It continues to format, and every ten seconds scsictl issues a TEST UNIT READY command to check the associated sense data. This associated sense data has a progress indicator which indicates how far the format is progress- ing. Note well that most SCSI disk drives prior to a few years ago do not support this option. identify Identify the specified device, displaying the device's SCSI bus, target, and lun, as well as the device's vendor, prod- uct, and revision strings. reassign blkno [blkno [...]] Issues a REASSIGN BLOCKS command to the device, adding the specified blocks to the grown defect list. This command is only supported on direct access devices. release Send a ``RELEASE'' command to the device to release a reservation on it. reserve Send a ``RESERVE'' command to the device to place a reser- vation on it. reset Reset the device. This command is only supported for devices which support the SCIOCRESET ioctl. start Send a ``START'' command to the device. This is useful typically only for disk devices. stop Send a ``STOP'' command to the device. This is useful typ- ically only for disk devices. tur Send a ``TEST UNIT READY'' command to the device. This is useful for generating current device status. getcache Returns basic cache parameters for the device. setcache none|r|w|rw [save] Set basic cache parameters for the device. The cache may be disabled (none), the read cache enabled (r), the write cache enabled (w), or both read and write cache enabled (rw). If the drive's cache parameters are savable, speci- fying save after the cache enable state will cause the parameters to be saved in non-volatile storage. flushcache Explicitly flushes the write cache. setspeed speed Set the highest speed that the optical drive should use for reading data. The units are multiples of a single speed CDROM (150 KB/s). Specify 0 to use the drive's fastest speed. getrealloc Returns automatic reallocation parameters for the device. setrealloc none|r|w|rw [save] Set automatic reallocation parameters for the device. Automatic reallocation may be disabled (none), the auto- matic read reallocation enabled (r), the automatic write reallocation enabled (w), or both automatic read and write reallocation enabled (rw). If the drive's automatic real- location parameters are savable, specifying save after the automatic reallocation enable state will cause the parame- ters to be saved in non-volatile storage.
BUS COMMANDS
The following commands are supported for SCSI busses: reset Reset the SCSI bus. This command is only supported if the host adapter supports the SCBUSIORESET ioctl. scan target lun Scan the SCSI bus for devices. This is useful if a device was not connected or powered on when the system was booted. The target and lun arguments specify which SCSI target and lun on the bus is to be scanned. Either may be wildcarded by specifying the keyword ``any'' or ``all''. detach target lun Detach the specified device from the bus. Useful if a device is powered down after use. The target and lun arguments have the same meaning as for the scan command, and may also be wildcarded.
NOTES
When scanning the SCSI bus, information about newly recognized devices is printed to console. No information is printed for already probed devices.
FILES
/dev/scsibus* - for commands operating on SCSI busses
SEE ALSO
ioctl(2), cd(4), ch(4), scsi(4), sd(4), se(4), ss(4), st(4), uk(4), atactl(8), dkctl(8)
HISTORY
The scsictl command first appeared in NetBSD 1.4.
AUTHORS
The scsictl command was written by Jason R. Thorpe of the Numerical Aero- space Simulation Facility, NASA Ames Research Center. NetBSD 8.3 November 19, 2016 NetBSD 8.3

Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.