gpioctl(8) - NetBSD Manual Pages

GPIOCTL(8)              NetBSD System Manager's Manual              GPIOCTL(8)


NAME
gpioctl -- control GPIO devices
SYNOPSIS
gpioctl [-qs] device gpioctl [-q] device attach device offset mask [flag] gpioctl [-qs] device pin [0 | 1 | 2] gpioctl [-qs] device pin [on | off | toggle] gpioctl [-q] device pin set [flags] [name] gpioctl [-q] device pin unset
DESCRIPTION
The gpioctl program allows manipulation of GPIO (General Purpose Input/Output) device pins. Such devices can be either part of the chipset or embedded CPU, or a separate chip. The usual way of using GPIO is to connect some simple devices such as LEDs and 1-wire thermal sensors to its pins. Each GPIO device has an associated device file in the /dev directory. device can be specified with or without the /dev prefix. For example, /dev/gpio0 or gpio0. GPIO pins can be either ``read'' or ``written'' with the values of logi- cal 0 or 1. If only a pin number is specified on the command line, the pin state will be read from the GPIO controller and displayed. To write to a pin, a value must be specified after the pin number. Values can be either 0 or 1. A value of 2 ``toggles'' the pin, i.e. changes its state to the opposite. Instead of the numerical values, the word on, off, or toggle can be used. Only pins that have been configured at securelevel 0, typically during system startup, are accessible once the securelevel has been raised. Pins can be given symbolic names for easier use. Besides using individ- ual pins, device drivers that use GPIO pins can be attached to a gpio(4) device using the gpioctl command. Such drivers can be detached at run- time using the drvctl(8) command. The following configuration flags are supported by the GPIO framework: in input direction out output direction inout bi-directional od open-drain output pp push-pull output tri tri-state (output disabled) pu internal pull-up enabled pd internal pull-down enabled iin invert input iout invert output pulsate pulsate output at a hardware-defined frequency and duty cycle Note that not all the flags may be supported by the particular GPIO con- troller. When executed with only the gpio(4) device name as argument, gpioctl reads information about the GPIO device and displays it. At securelevel 0 the number of physically available pins is displayed, at higher securelevels the number of configured (set) pins is displayed. The options are as follows: -q Operate quietly i.e. nothing is printed to stdout. -s Only output a single number on stdout, representing either the state of the pin or the number of available pins if no pin number was passed as argument. This option is useful e.g. when gpioctl is used in shell scripts to query the state of a pin.
FILES
/dev/gpiou GPIO device unit u file.
EXAMPLES
Configure pin 20 to have push-pull output: # gpioctl gpio0 20 set out pp Write logical 1 to pin 20: # gpioctl gpio0 20 1 Attach a onewire(4) bus on a gpioow(4) device on pin 4: # gpioctl gpio0 attach gpioow 4 0x01 Detach the gpioow0 device: # drvctl -d gpioow0 Configure pin 5 as output and name it error_led: # gpioctl gpio0 5 set out error_led Toggle the error_led: # gpioctl gpio0 error_led 2
SEE ALSO
gpio(4), drvctl(8)
HISTORY
The gpioctl command first appeared in OpenBSD 3.6 and NetBSD 4.0.
AUTHORS
The gpioctl program was written by Alexander Yurchenko <grange@openbsd.org>. Device attachment was added by Marc Balmer <marc@msys.ch>. NetBSD 8.2 May 19, 2013 NetBSD 8.2

Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.