tunefs(8) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
TUNEFS(8)               NetBSD System Manager's Manual               TUNEFS(8)


NAME

     tunefs -- tune up an existing file system


SYNOPSIS

     tunefs [-AFN] [-e maxbpg] [-g avgfilesize] [-h avgfpdir] [-l logsize]
            [-m minfree] [-o optimize_preference] [-q quota] [-S sectorsize]
            special | filesys


DESCRIPTION

     tunefs is designed to change the dynamic parameters of a file system
     which affect the layout policies.

     The following options are supported by tunefs:

     -A      Cause the values to be updated in all the alternate superblocks
             instead of just the standard superblock.  If this option is not
             used, then use of a backup superblock by fsck(8) will lose any-
             thing changed by tunefs.  -A is ignored when -N is specified.

     -F      Indicates that special is a file system image, rather than a
             device name or file system mount point.  special will be accessed
             `as-is'.

     -N      Display all the settable options (after any changes from the tun-
             ing options) but do not cause any of them to be changed.

     -e maxbpg
             This indicates the maximum number of blocks any single file can
             allocate out of a cylinder group before it is forced to begin
             allocating blocks from another cylinder group.  Typically this
             value is set to about one quarter of the total blocks in a cylin-
             der group.  The intent is to prevent any single file from using
             up all the blocks in a single cylinder group, thus degrading
             access times for all files subsequently allocated in that cylin-
             der group.  The effect of this limit is to cause big files to do
             long seeks more frequently than if they were allowed to allocate
             all the blocks in a cylinder group before seeking elsewhere.  For
             file systems with exclusively large files, this parameter should
             be set higher.

     -g avgfilesize
             This specifies the expected average file size.

     -h avgfpdir
             This specifies the expected number of files per directory.

     -l logsize
             This value specifies the size of the in-filesystem journaling log
             file.  The default journaling log file size is described in
             wapbl(4).  Specifying a size of zero will cause the in-filesystem
             journaling log file to be removed the next time the filesystem is
             mounted.  The size of an existing in-filesystem journaling log
             file can not be changed directly.  You need to first set the log
             file size to zero, then mount the filesystem without logging
             enabled (which will remove the log without creating a new one),
             unmount, set the size to the new value and finally re-mount with
             logging enabled.

     -m minfree
             This value specifies the percentage of space held back from nor-
             mal users; the minimum free space threshold.  The default value
             is set during creation of the filesystem, see newfs(8).  This
             value can be set to zero, however up to a factor of three in
             throughput will be lost over the performance obtained at a 5%
             threshold.  Note that if the value is raised above the current
             usage level, users will be unable to allocate files until enough
             files have been deleted to get under the higher threshold.

     -o optimize_preference
             The file system can either try to minimize the time spent allo-
             cating blocks, or it can attempt to minimize the space fragmenta-
             tion on the disk.  If the value of minfree (see above) is less
             than 5%, then the file system should optimize for space to avoid
             running out of full sized blocks.  For values of minfree greater
             than or equal to 5%, fragmentation is unlikely to be problemati-
             cal, and the file system can be optimized for time.

             optimize_preference can be specified as either space or time.

     -q quota
             enable or disable a quota.  quota can be one of user, group,
             nouser or nogroup to enable or disable the specified quota type.
             Multiple -q can be used to enable/disable all types at once.

             After enabling a quota, fsck_ffs(8) has to be run to compute the
             correct quota values.

     -S sectorsize
             changes the fsbtodb value in the superblock to reflect a particu-
             lar physical sector size.  This value is ignored by the NetBSD
             kernel but needed by tools like fsck_ffs(8) to access disk blocks
             correctly.  The minimum value is DEV_BSIZE (512).

             Changing the fsbtodb value becomes necessary when a filesystem
             image is created for one sector size and then transferred to a
             device with a different sector size and should be applied also to
             the alternate superblocks.


SEE ALSO

     wapbl(4), fs(5), dumpfs(8), fsck_ffs(8), newfs(8)

     M. McKusick, W. Joy, S. Leffler, and R. Fabry, "A Fast File System for
     UNIX", ACM Transactions on Computer Systems 2, 3, pp 181-197, August
     1984, (reprinted in the BSD System Manager's Manual, SMM:5).


HISTORY

     The tunefs command appeared in 4.2BSD.


BUGS

     This program should work on mounted and active file systems.  Because the
     super-block is not kept in the buffer cache, the changes will only take
     effect if the program is run on unmounted file systems.  To change the
     root file system, the system must be rebooted after the file system is
     tuned.

     You can tune a file system, but you can't tune a fish.

NetBSD 8.0                      August 9, 2014                      NetBSD 8.0