rtsold(8) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
RTSOLD(8)               NetBSD System Manager's Manual               RTSOLD(8)


NAME

     rtsold -- router solicitation daemon


SYNOPSIS

     rtsold [-1Ddfm] interface ...
     rtsold [-1Ddfm] -a
     rtsol [-Dd] interface ...
     rtsol [-Dd] -a


DESCRIPTION

     rtsold is the daemon program to send ICMPv6 Router Solicitation messages
     on the specified interfaces.  If a node (re)attaches to a link, rtsold
     sends some Router Solicitations on the link destined to the link-local
     scope all-routers multicast address to discover new routers and to get
     non link-local addresses.

     rtsold should be used on IPv6 hosts (non-router nodes) only.

     If you invoke the program as rtsol, it will transmit probes from the
     specified interface, without becoming a daemon.  In other words, rtsol
     behaves as ``rtsold -f1 interface ...''.

     Specifically, rtsold sends at most 3 Router Solicitations on an interface
     after one of the following events:

     ·   Just after invocation of the rtsold daemon.

     ·   The interface is up after a temporary interface failure.  rtsold
         detects such failures by periodically probing to see if the status of
         the interface is active or not.  Note that some network cards and
         drivers do not allow the extraction of link state.  In such cases,
         rtsold cannot detect the change of the interface status.

     ·   Every 60 seconds if the -m option is specified and the rtsold daemon
         cannot get the interface status.  This feature does not conform to
         the IPv6 neighbor discovery specification, but is provided for mobile
         stations.  The default interval for router advertisements, which is
         approximately 10 minutes, is slightly long for mobile stations.  This
         feature is provided for such stations so that they can find new
         routers as soon as possible when they attach to another link.

     Once rtsold has sent a Router Solicitation, and has received a valid
     Router Advertisement, it refrains from sending additional solicitations
     on that interface, until the next time one of the above events occurs.

     When sending a Router Solicitation on an interface, rtsold includes a
     Source Link-layer address option if the interface has a link-layer
     address.

     Upon receipt of signal SIGUSR1, rtsold will dump the current internal
     state into /var/run/rtsold.dump.  Also note that rtsold will not be able
     to update the kernel routing tables unless sysctl(8) reports that
     net.inet6.ip6.accept_rtadv=1.

     The options are as follows:

     -1      Perform only one probe.  Transmit Router Solicitation packets
             until at least one valid Router Advertisement packet has arrived
             on each interface, then exit.

     -a      Autoprobe outgoing interfaces.  rtsold will try to find a non-
             loopback, non-point-to-point, IPv6-capable interfaces, and send
             router solicitation messages on all of them.

     -D      Enable more debugging (than that offered by the -d option)
             including the printing of internal timer information.

     -d      Enable debugging.

     -f      This option prevents rtsold from becoming a daemon (foreground
             mode).  Warning messages are generated to standard error instead
             of syslog(3).

     -m      Enable mobility support.  If this option is specified, rtsold
             sends probing packets to default routers that have advertised
             Router Advertisements when the node (re)attaches to an interface.
             Moreover, if the option is specified, rtsold periodically sends
             Router Solicitation on an interface that does not support the
             SIOCGIFMEDIA ioctl.


EXIT STATUS

     The rtsold utility exits 0 on success, and >0 if an error occurs.


FILES

     /var/run/rtsold.pid     The PID of the currently running rtsold.
     /var/run/rtsold.dump    Internal state dump file.


SEE ALSO

     rtadvd(8), sysctl(8)


HISTORY

     The rtsold command is based on the rtsol command, which first appeared in
     the WIDE/KAME IPv6 protocol stack kit.  rtsol is now integrated into
     rtsold.


BUGS

     In some operating systems, when a PCMCIA network card is removed and
     reinserted, the corresponding interface index is changed.  However,
     rtsold assumes such changes will not occur, and always uses the index
     that it got at invocation.  As a result, rtsold may not work if you rein-
     sert a network card.  In such a case, rtsold should be killed and
     restarted.

     You may see kernel error messages if you try to autoconfigure a host with
     multiple interfaces.

NetBSD 7.1.2                     May 24, 2013                     NetBSD 7.1.2