- NetBSD Manual Pages
SAVECORE(8) NetBSD System Manager's Manual SAVECORE(8)
Powered by man-cgi (2021-06-01).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
savecore -- save a core dump of the operating system
savecore [-fvz] [-N system] [-Z level] [directory]
savecore -c [-v] [-N system]
savecore -n [-v] [-N system]
When the NetBSD kernel encounters a fatal error, the panic(9) routine
arranges for a snapshot of the contents of physical memory to be written
into a dump area, typically in the swap partition.
Upon a subsequent reboot, savecore is typically run out of rc(8), before
swapping is enabled, to copy the kernel and the saved memory image into
directory, and enters a reboot message and information about the core
dump into the system log. If a directory is not specified, then
/var/crash is used.
The kernel and core file can then be analyzed using various tools,
including crash(8), dmesg(8), fstat(1), gdb(1), iostat(8), netstat(1),
ps(1), and pstat(8), to attempt to deduce the cause of the crash.
Crashes are usually the result of hardware faults or kernel bugs. If a
kernel bug is suspected, a full bug report should be filed at
http://www.netbsd.org/, or using send-pr(1), containing as much informa-
tion as possible about the circumstances of the crash. Since crash dumps
are typically very large and may contain whatever (potentially confiden-
tial) information was in memory at the time of the crash, do NOT include
a copy of the crash dump file in the bug report; instead, save it some-
where in the event that a NetBSD developer wants to examine it.
The options are as follows:
-c Only clears the dump without saving it, so that future invoca-
tions of savecore will ignore it.
-f Forces a dump to be taken even if the dump doesn't appear cor-
rect or there is insufficient disk space.
-n Check whether a dump is present without taking further action.
The command exits with zero status if a dump is present, or
with non-zero status otherwise.
-N Use system as the kernel instead of the default (returned by
getbootfile(3)). Note that getbootfile(3) uses secure_path(3)
to check that kernel file is ``secure'' and will default to
/netbsd if the check fails.
-v Prints out some additional debugging information.
-z Compresses the core dump and kernel (see gzip(1)).
-Z level Set the compression level for -z to level. Defaults to 1 (the
fastest compression mode). Refer to gzip(1) for more informa-
tion regarding the compression level.
savecore checks the core dump in various ways to make sure that it is
current and that it corresponds to the currently running system. If it
passes these checks, it saves the core image in directory/netbsd.#.core
and the system in directory/netbsd.# (or in directory/netbsd.#.core.gz
and directory/netbsd.#.gz, respectively, if the -z option is used). The
``#'' is the number from the first line of the file directory/bounds, and
it is incremented and stored back into the file each time savecore suc-
savecore also checks the available disk space before attempting to make
the copies. If there is insufficient disk space in the file system con-
taining directory, or if the file directory/minfree exists and the number
of free kilobytes (for non-superusers) in the file system after the
copies were made would be less than the number in the first line of this
file, the copies are not attempted.
If savecore successfully copies the kernel and the core dump, the core
dump is cleared so that future invocations of savecore will ignore it.
fstat(1), gdb(1), gzip(1), netstat(1), ps(1), send-pr(1), crash(8),
dmesg(8), iostat(8), pstat(8), rc(8), syslogd(8), panic(9)
The savecore command appeared in 4.1BSD.
The minfree code does not consider the effect of compression.
NetBSD 7.1.2 September 13, 2011 NetBSD 7.1.2