ffb(4) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
FFB(4)              NetBSD/sparc64 Kernel Interfaces Manual             FFB(4)


NAME

     ffb -- Sun accelerated 24-bit color frame buffer


SYNOPSIS

     ffb* at mainbus0 addr 0xff8de000: Creator3D, model SUNW,501-4790, dac 10
     (UltraSPARC II horizontal)
     ffb* at mainbus0 addr 0xfeb80000: Creator3D, model SUNW,501-4788, dac 10
     (UltraSPARC II vertical)
     ffb* at mainbus0: Elite3D, model SUNW,540-3623, dac 10
     (UltraSPARC II vertical)
     ffb* at upa0: Creator3D, model SUNW,501-4788, dac 10
     (UltraSPARC III vertical)
     ffb* at upa0: Elite3D, model SUNW,540-3623, dac 10
     (UltraSPARC III vertical)


DESCRIPTION

     The ffb is a UPA based color frame buffer, found in some Sun SBus and PCI
     systems.  The ffb driver supports both the Creator/Creator3D, and the
     Elite3D frame buffers.

     There are several versions of the ffb board.  The Sun part numbers and
     board types are:

           501-2634      Creator Series 1 (FFB)
                         Ultra1, Ultra2
           501-4127      Creator Series 1 (FFB)
                         Ultra1, Ultra2, Enterprisexx00
           501-2633      Creator 3D Series 1 (FFB)
                         Ultra1, Ultra2
           501-3129      Creator 3D Series 1 (FFB)
                         Ultra1, Ultra2, Enterprisexx00
           501-4126      Creator 3D Series 1 (FFB)
                         Ultra1, Ultra2
           501-4174      Creator Series 2 (FFB2)
                         Ultra 30, Ultra 60
           501-4173      Creator3D Series 2 (FFB2)
                         Ultra1, Ultra2, Enterprisexx00
           501-4172      Creator3D Series 2 (FFB2)
                         Ultra30, Ultra60
           501-4789      Creator Series 3 (FFB2+)
                         Ultra10, Ultra30, Ultra60
           501-4790      Creator 3D Series 3 (FFB2+)
                         Ultra2, Enterprisexx00
           501-4788, 501-5690
                         Creator 3D Series 3 (FFB2+)
                         Ultra10, Ultra30, Ultra60, Blade1000, Blade2000
           501-4860, 501-5268, 501-5201, 501-5484
                         Elite3D-m3 Series 1 (AFB)
                         Ultra10, Ultra30, Ultra60, Ultra80
           540-3623, 540-3902
                         Elite3D-m6 Series 1 (AFB)
                         Ultra10, Ultra30, Ultra60, Ultra80
           501-5574, 501-5575
                         Elite3D-m3 Series 2 (AFB)
                         Ultra10, Ultra30, Ultra60, Ultra80, Blade1000,
                         Blade2000
           540-4313      Elite3D-m6 Series 2 (AFB)
                         Ultra10, Ultra30, Ultra60, Ultra80, Blade1000,
                         Blade2000
           540-3058, 540-3979, 540-4335
                         Elite3D-m6 (AFB)
                         Ultra2, Ultra450, Enterprisexx00

     The `Creator' cards have 5MB of on-board memory, support a maximum graph-
     ics resolution of 1280x1024, and are single-buffered.

     The `Creator3D' cards have 15MB of on-board memory support a maximum res-
     olution of 1280x1024 double-buffered, and 1920x1360 single-buffered.

     The `Elite3D' cards have 15MB of on-board memory, support a maximum reso-
     lution of 1280x1024, and are always double-buffered.  The `Elite3D-m3'
     cards have one hardware geometry engine, whereas the `Elite3D-m6' cards
     have two.

     The `Series 3' cards are considerably faster than the `Series 1' and
     `Series 2' cards.

     The ffb driver supports reading EDID data from connected monitors, and
     will automatically set a resolution that is supported by both the card
     and the monitor if the EDID data can be read.  This can be overridden for
     the console frame buffer, by setting the output-device openprom variable.
     For example, the following openprom command will set the console resolu-
     tion to 1280x1024 @ 60Hz, which will not be altered by the ffb driver.

           setenv output-device screen:r1280x1024x60


SEE ALSO

     eeprom(8)


BUGS

     It is necessary to blank the video output when reading EDID data.

     The ffb driver does not support 3D acceleration.

     Not all 13W3 to VGA converters connect 13W3 pin 2 to VGA pin 9.  This pin
     supplies +5V DC to power the monitor EEPROM, even when the monitor is
     powered off, and is necessary in order to obtain EDID data on some moni-
     tors.

     Adapters that are known to connect these pins are:

           530-2917      13W3 cable
           130-3034      VGA cable

     Adapters that are known not to connect these pins are:

           530-2357      13W3 cable

NetBSD 6.0                       April 1, 2011                      NetBSD 6.0