PCI_CONFIGURE_BUS(9) NetBSD Kernel Developer's Manual PCI_CONFIGURE_BUS(9)
NAME
pci_configure_bus, pci_conf_hook, pci_conf_interrupt -- perform PCI bus configuration
SYNOPSIS
#include <dev/pci/pciconf.h> int pci_configure_bus(pci_chipset_tag_t pc, struct extent *ioext, struct extent *memext, struct extent *pmemext, int firstbus, int cacheline_size);
DESCRIPTION
The pci_configure_bus() function configures a PCI bus for use. This involves: · Defining bus numbers for all busses on the system, · Setting the Base Address Registers for all devices, · Setting up the interrupt line register for all devices, · Configuring bus latency timers for all devices, and · Configuring cacheline sizes for all devices. In traditional PCs and Alpha systems, the BIOS or firmware takes care of this task, but that is not the case for all systems. pci_configure_bus() should be called prior to the autoconfiguration of the bus. The pc argument is a machine-dependent tag used to specify the PCI chipset to the system. This should be the same value used with pci_make_tag(). The extent arguments define memory extents from which the address space for the cards will be taken. These addresses should be in the PCI address space. The ioext extent is for PCI I/O accesses. The memext extent is for PCI memory accesses that might have side effects. I.e., that can not be cached. The pmemext extent is for PCI memory accesses that can be cached. The pmemext extent will be used for any ROMs and any memory regions that are marked as ``prefetchable'' in their BAR. If an implementation does not distinguish between prefetchable and non-prefetchable memory, it may pass NULL for pmemext. In this case, prefetchable memory allocations will be made from the non-prefetchable region. The firstbus argument indicates the number of the first bus to be configured. The cacheline_size argument is used to configure the PCI Cache Line Size Register; it should be the size, in bytes, of the largest D-cache line on the system. An implementation may choose to not have full configuration performed by pci_configure_bus() on certain PCI devices, such as PCI host bridges or PCI bus analyzers which are instantiated as devices on the bus. In order for this to take place, the header <machine/pci_machdep.h> must define the __HAVE_PCI_CONF_HOOK symbol (without a value), and a machine-depen- dent function pci_conf_hook() (declared in the same header) must be defined. The prototype for this function is int pci_conf_hook(pci_chipset_tag_t pc, int bus, int device, int function, pcireg_t id) In this function, bus, device, and function uniquely identify the item being configured; in addition to this, the value of the device's PCI identification register is passed in id. For each device pci_conf_hook() can then decide upon the amount of configuration to be performed by returning a bitwise inclusive-or of the following flags: PCI_CONF_MAP_IO Configure Base Address Registers that map I/O space PCI_CONF_MAP_MEM Configure Base Address Registers that map mem- ory space PCI_CONF_MAP_ROM Configure Expansion ROM Base Address register PCI_CONF_ENABLE_IO Enable I/O space accesses PCI_CONF_ENABLE_MEM Enable memory space accesses PCI_CONF_ENABLE_BM Enable bus mastering In addition, PCI_CONF_ALL specifies all of the above. One of the functions of pci_configure_bus() is to configure interrupt ``line'' information. This must be done on a machine-dependent basis, so a machine-dependent function pci_conf_interrupt() must be defined. The prototype for this function is void pci_conf_interrupt(pci_chipset_tag_t pc, int bus, int device, int pin, int swiz, int *iline) In this function, bus, device, and pin, uniquely identify the item being configured. The swiz argument is a ``swizzle'', a sum of the device num- bers of the primary interface of the bridges between the host bridge and the current device. The function is responsible for setting the value of iline. See chapter 9 of the ``PCI-to-PCI Bridge Architecture Specification'' for more information on swizzling (also known as inter- rupt routing).
RETURN VALUES
If successful pci_configure_bus() returns 0. A non-zero return value means that the bus was not completely configured for some reason. A description of the failure will be displayed on the console.
ENVIRONMENT
The pci_configure_bus() function is only included in the kernel if the kernel is compiled with the PCI_NETBSD_CONFIGURE option enabled.
EXAMPLES
The pci_conf_hook() function in evbppc's walnut implementation looks like: int pci_conf_hook(pci_chipset_tag_t pc, int bus, int dev, int func, pcireg_t id) { if ((PCI_VENDOR(id) == PCI_VENDOR_IBM && PCI_PRODUCT(id) == PCI_PRODUCT_IBM_405GP) || (PCI_VENDOR(id) == PCI_VENDOR_INTEL && PCI_PRODUCT(id) == PCI_PRODUCT_INTEL_80960_RP)) { /* Don't configure the bridge and PCI probe. */ return 0; } return (PCI_CONF_ALL & ~PCI_CONF_MAP_ROM); } The pci_conf_interrupt() function in the sandpoint implementation looks like: void pci_conf_interrupt(pci_chipset_tag_t pc, int bus, int dev, int pin, int swiz, int *iline) { if (bus == 0) { *iline = dev; } else { *iline = 13 + ((swiz + dev + 3) & 3); } } The BeBox has nearly 1GB of PCI I/O memory starting at processor address 0x81000000 (PCI I/O address 0x01000000), and nearly 1GB of PCI memory starting at 0xC0000000 (PCI memory address 0x00000000). The pci_configure_bus() function might be called as follows: struct extent *ioext, *memext; ... ioext = extent_create("pciio", 0x01000000, 0x0fffffff, M_DEVBUF, NULL, 0, EX_NOWAIT); memext = extent_create("pcimem", 0x00000000, 0x0fffffff, M_DEVBUF, NULL, 0, EX_NOWAIT); ... pci_configure_bus(0, ioext, memext, NULL); ... extent_destroy(ioext); extent_destroy(memext); ... Note that this must be called before the PCI bus is attached during auto- configuration.
SEE ALSO
pci(4), extent(9)
HISTORY
pci_configure_bus() was added in NetBSD 1.6. NetBSD 5.2 February 21, 2006 NetBSD 5.2
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.