dkctl(8) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
DKCTL(8)                NetBSD System Manager's Manual                DKCTL(8)


NAME

     dkctl -- program to manipulate disks


SYNOPSIS

     dkctl device command [arg [...]]


DESCRIPTION

     dkctl allows a user or system administrator to manipulate and configure
     disks in various ways.  It is used by specifying a disk to manipulate,
     the command to perform, and any arguments the command may require.


COMMANDS

     The following commands are supported:

     getcache            Get and display the cache enables for the specified
                         device.

     setcache none | r | w | rw [save]
                         Set the cache enables for the specified device.  The
                         enables are as follows:

                               none    Disable all caches on the disk.

                               r       Enable the read cache, and disable all
                                       other caches on the disk.

                               w       Enable the write cache, and disable all
                                       other caches on the disk.

                               rw      Enable both the read and write caches
                                       on the disk.

                               save    If specified, and the cache enables are
                                       savable, saves the cache enables in the
                                       disk's non-volatile parameter storage.

     synccache [force]   Causes the cache on the disk to be synchronized,
                         flushing all dirty write cache blocks to the media.
                         If force is specified, the cache synchronization com-
                         mand will be issued even if the kernel does not
                         believe that there are any dirty cache blocks in the
                         disk's cache.

     keeplabel [yes | no]
                         Specify to keep or drop the in-core disklabel on the
                         last close of the disk device.  (Keep if yes is spec-
                         ified, drop if no is specified.)

     badsector flush | list | retry
                         Used for managing the kernel's bad sector list for
                         wd(4) devices.  The software bad sector list is only
                         maintained if the option ``WD_SOFTBADSECT'' was spec-
                         ified on kernel configuration.

                               flush     Clears the in kernel list of bad sec-
                                         tors.

                               list      Prints out the list of bad sector
                                         ranges recorded by the kernel.

                               retry     Flushes the in kernel list and then
                                         retries all of the previously
                                         recorded bad sectors, causing the
                                         list to self update.  This option can
                                         only be used with character devices.

     addwedge name startblk blkcnt ptype
                         Define a ``wedge'' on the specified disk starting at
                         block number startblk and spanning blkcnt blocks.
                         The wedge will have the volume name name and the par-
                         tition type ptype.  Valid choices for ptype would be
                         unused, swap, ffs, lfs, ext2fs, cd9660, ados, hfs,
                         msdos, filecore, raidframe, ccd, appleufs, ntfs, and
                         cgd.

                         The device name of the virtual block device assigned
                         to the wedge will be displayed after the wedge has
                         been successfully created.  See dk(4) for more infor-
                         mation about disk wedges.

     delwedge dk         Delete the wedge specified by its device name dk from
                         the specified disk.

     getwedgeinfo        Display information about the specified disk wedge.

     listwedges          List all of the wedges configured on the specified
                         disk.

     strategy [name]     Get and set the disk I/O scheduler (buffer queue
                         strategy) on the drive.  If you do not provide a name
                         argument, the currently selected strategy will be
                         shown.  To set the bufq strategy, the name argument
                         must be specified.  name must be the name of one of
                         the built-in kernel disk I/O schedulers.  To get the
                         list of supported schedulers, use the following com-
                         mand:

                               $ sysctl kern.bufq.strategies


SEE ALSO

     ioctl(2), dk(4), sd(4), wd(4), disklabel(5), atactl(8), scsictl(8)


HISTORY

     The dkctl command first appeared in NetBSD 1.6.


AUTHORS

     The dkctl command was written by Jason R. Thorpe of Wasabi Systems, Inc.

NetBSD 5.1.2                     July 30, 2009                    NetBSD 5.1.2