bus_dma(9) - NetBSD Manual Pages

BUS_DMA(9)             NetBSD Kernel Developer's Manual             BUS_DMA(9)


NAME
bus_dma, bus_dmamap_create, bus_dmamap_destroy, bus_dmamap_load, bus_dmamap_load_mbuf, bus_dmamap_load_uio, bus_dmamap_load_raw, bus_dmamap_unload, bus_dmamap_sync, bus_dmamem_alloc, bus_dmamem_free, bus_dmamem_map, bus_dmamem_unmap, bus_dmamem_mmap, bus_dmatag_subregion, bus_dmatag_destroy -- Bus and Machine Independent DMA Mapping Interface
SYNOPSIS
#include <machine/bus.h> int bus_dmamap_create(bus_dma_tag_t tag, bus_size_t size, int nsegments, bus_size_t maxsegsz, bus_size_t boundary, int flags, bus_dmamap_t *dmamp); void bus_dmamap_destroy(bus_dma_tag_t tag, bus_dmamap_t dmam); int bus_dmamap_load(bus_dma_tag_t tag, bus_dmamap_t dmam, void *buf, bus_size_t buflen, struct lwp *l, int flags); int bus_dmamap_load_mbuf(bus_dma_tag_t tag, bus_dmamap_t dmam, struct mbuf *chain, int flags); int bus_dmamap_load_uio(bus_dma_tag_t tag, bus_dmamap_t dmam, struct uio *uio, int flags); int bus_dmamap_load_raw(bus_dma_tag_t tag, bus_dmamap_t dmam, bus_dma_segment_t *segs, int nsegs, bus_size_t size, int flags); void bus_dmamap_unload(bus_dma_tag_t tag, bus_dmamap_t dmam); void bus_dmamap_sync(bus_dma_tag_t tag, bus_dmamap_t dmam, bus_addr_t offset, bus_size_t len, int ops); int bus_dmamem_alloc(bus_dma_tag_t tag, bus_size_t size, bus_size_t alignment, bus_size_t boundary, bus_dma_segment_t *segs, int nsegs, int *rsegs, int flags); void bus_dmamem_free(bus_dma_tag_t tag, bus_dma_segment_t *segs, int nsegs); int bus_dmamem_map(bus_dma_tag_t tag, bus_dma_segment_t *segs, int nsegs, size_t size, void **kvap, int flags); void bus_dmamem_unmap(bus_dma_tag_t tag, void *kva, size_t size); paddr_t bus_dmamem_mmap(bus_dma_tag_t tag, bus_dma_segment_t *segs, int nsegs, off_t off, int prot, int flags); int bus_dmatag_subregion(bus_dma_tag_t tag, bus_addr_t min_addr, bus_addr_t max_addr, bus_dma_tag_t *newtag, int flags); void bus_dmatag_destroy(bus_dma_tag_t tag);
DESCRIPTION
Provide a bus- and machine-independent "DMA mapping interface."
NOTES
All data structures, function prototypes, and macros will be defined by the port-specific header <machine/bus.h>. Note that this document assumes the existence of types already defined by the current "bus.h" interface. Unless otherwise noted, all function calls in this interface may be defined as cpp(1) macros.
DATA TYPES
Individual implementations may name these structures whatever they wish, providing that the external representations are: bus_dma_tag_t A machine-dependent opaque type describing the implementation of DMA for a given bus. bus_dma_segment_t A structure with at least the following members: bus_addr_t ds_addr; bus_size_t ds_len; The structure may have machine-dependent members and arbitrary layout. The values in ds_addr and ds_len are suitable for pro- gramming into DMA controller address and length registers. bus_dmamap_t A pointer to a structure with at least the following members: bus_size_t dm_maxsegsz; bus_size_t dm_mapsize; int dm_nsegs; bus_dma_segment_t *dm_segs; The structure may have machine-dependent members and arbitrary layout. The dm_maxsegsz member indicates the maximum number of bytes that may be transferred by any given DMA segment. The dm_mapsize member indicates the size of the mapping. A value of 0 indicates the mapping is invalid. The dm_segs member may be an array of segments or a pointer to an array of segments. The dm_nsegs member indicates the number of segments in dm_segs.
FUNCTIONS
bus_dmamap_create(tag, size, nsegments, maxsegsz, boundary, flags, dmamp) Allocates a DMA handle and initializes it according to the parameters provided. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. size This is the maximum DMA transfer that can be mapped by the handle. nsegments Number of segments the device can support in a single DMA transaction. This may be the number of scatter- gather descriptors supported by the device. maxsegsz The maximum number of bytes that may be transferred by any given DMA segment and will be assigned to the dm_maxsegsz member. boundary Some DMA controllers are not able to transfer data that crosses a particular boundary. This argument allows this boundary to be specified. The boundary lines begin at 0, and occur every boundary bytes. Mappings may begin on a boundary line but may not end on or cross a boundary line. If no boundary condi- tion needs to be observed, a boundary argument of 0 should be used. flags Flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. BUS_DMA_ALLOCNOW Perform any resource allocation this handle may need now. If this is not specified, the allocation may be deferred to bus_dmamap_load(). If this flag is specified, bus_dmamap_load() will not block on resource allocation. BUS_DMA_BUS[1-4] These flags are placeholders, and may be used by busses to provide bus-dependent functionality. dmamp This is a pointer to a bus_dmamap_t. A DMA map will be allocated and pointed to by dmamp upon successful completion of this routine. dmamp is undefined if this routine fails. Behavior is not defined if invalid arguments are passed to bus_dmamap_create(). Returns 0 on success, or an error code to indicate mode of fail- ure. bus_dmamap_destroy(tag, dmam) Frees all resources associated with a given DMA handle. Argu- ments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. dmam The DMA handle to destroy. In the event that the DMA handle contains a valid mapping, the mapping will be unloaded via the same mechanism used by bus_dmamap_unload(). Behavior is not defined if invalid arguments are passed to bus_dmamap_destroy(). If given valid arguments, bus_dmamap_destroy() always succeeds. bus_dmamap_load(tag, dmam, buf, buflen, l, flags) Loads a DMA handle with mappings for a DMA transfer. It assumes that all pages involved in a DMA transfer are wired. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. dmam The DMA handle with which to map the transfer. buf The buffer to be used for the DMA transfer. buflen The size of the buffer. l Used to indicate the address space in which the buffer is located. If NULL, the buffer is assumed to be in kernel space. Otherwise, the buffer is assumed to be in lwp l's address space. flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. BUS_DMA_STREAMING By default, the bus_dma API assumes that there is coherency between mem- ory and the device performing the DMA transaction. Some platforms, how- ever, have special hardware, such as an ``I/O cache'', which may improve performance of some types of DMA transactions, but which break the assumption that there is coherency between memory and the device per- forming the DMA transaction. This flag allows the use of this special hardware, provided that the device is doing sequential, unidirectional transfers which conform to certain alignment and size constraints defined by the platform. If the platform does not support the fea- ture, or if the buffer being loaded into the DMA map does not conform to the constraints required for use of the feature, then this flag will be silently ignored. Also refer to the use of this flag with the bus_dmamem_alloc() function. BUS_DMA_READ This is a hint to the machine-depen- dent back-end that indicates the map- ping will be used only for a device -> memory transaction. The back-end may perform optimizations based on this information. BUS_DMA_WRITE This is a hint to the machine-depen- dent back-end that indicates the map- ping will be used only for a memory -> device transaction. The back-end may perform optimizations based on this information. BUS_DMA_BUS[1-4] These flags are placeholders, and may be used by busses to provide bus- dependent functionality. As noted above, if a DMA handle is created with BUS_DMA_ALLOCNOW, bus_dmamap_load() will never block. If a call to bus_dmamap_load() fails, the mapping in the DMA handle will be invalid. It is the responsibility of the caller to clean up any inconsistent device state resulting from incom- plete iteration through the uio. Behavior is not defined if invalid arguments are passed to bus_dmamap_load(). Returns 0 on success, or an error code to indicate mode of fail- ure. bus_dmamap_load_mbuf(tag, dmam, chain, flags) This is a variation of bus_dmamap_load() which maps mbuf chains for DMA transfers. Mbuf chains are assumed to be in kernel vir- tual address space. bus_dmamap_load_uio(tag, dmam, uio, flags) This is a variation of bus_dmamap_load() which maps buffers pointed to by uio for DMA transfers. Determination if the buffers are in user or kernel virtual address space is done internally, according to uio->uio_vmspace. See uiomove(9) for details of the uio structure. bus_dmamap_load_raw(tag, dmam, segs, nsegs, size, flags) This is a variation of bus_dmamap_load() which maps buffers allocated by bus_dmamem_alloc() (see below). The segs argument is an array of bus_dma_segment_t's filled in by bus_dmamem_alloc(). The nsegs argument is the number of seg- ments in the array. The size argument is the size of the DMA transfer. bus_dmamap_unload(tag, dmam) Deletes the mappings for a given DMA handle. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. dmam The DMA handle containing the mappings which are to be deleted. If the DMA handle was created with BUS_DMA_ALLOCNOW, bus_dmamap_unload() will not free the corresponding resources which were allocated by bus_dmamap_create(). This is to ensure that bus_dmamap_load() will never block on resources if the han- dle was created with BUS_DMA_ALLOCNOW. bus_dmamap_unload() will not perform any implicit synchroniza- tion of DMA buffers. This must be done explicitly by bus_dmamap_sync(). bus_dmamap_unload() will restore the dm_maxsegsz member to its initial value assigned by bus_dmamap_create(). Behavior is not defined if invalid arguments are passed to bus_dmamap_unload(). If given valid arguments, bus_dmamap_unload() always succeeds. bus_dmamap_sync(tag, dmam, offset, len, ops) Performs pre- and post-DMA operation cache and/or buffer syn- chronization. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. dmam The DMA mapping to be synchronized. offset The offset into the DMA mapping to synchronize. len The length of the mapping from offset to synchronize. ops One or more synchronization operation to perform. The following DMA synchronization operations are defined: BUS_DMASYNC_PREREAD Perform any pre-read DMA cache and/or bounce operations. BUS_DMASYNC_POSTREAD Perform any post-read DMA cache and/or bounce operations. BUS_DMASYNC_PREWRITE Perform any pre-write DMA cache and/or bounce operations. BUS_DMASYNC_POSTWRITE Perform any post-write DMA cache and/or bounce operations. More than one operation may performed in a given syn- chronization call. Mixing of PRE and POST operations is not allowed, and behavior is undefined if this is attempted. Synchronization operations are expressed from the perspective of the host RAM, e.g., a device -> memory operation is a READ and a memory -> device operation is a WRITE. bus_dmamap_sync() may consult state kept within the DMA map to determine if the memory is mapped in a DMA coherent fashion. If so, bus_dmamap_sync() may elect to skip certain expensive opera- tions, such as flushing of the data cache. See bus_dmamem_map() for more information on this subject. On platforms which implement a weak memory access ordering model, bus_dmamap_sync() will always cause the appropriate mem- ory barriers to be issued. This function exists to ensure that the host and the device have a consistent view of a range of DMA memory, before and after a DMA operation. An example of using bus_dmamap_sync(), involving multiple read- write use of a single mapping might look like this: bus_dmamap_load(...); while (not done) { /* invalidate soon-to-be-stale cache blocks */ bus_dmamap_sync(..., BUS_DMASYNC_PREREAD); [ do read DMA ] /* copy from bounce */ bus_dmamap_sync(..., BUS_DMASYNC_POSTREAD); /* read data now in driver-provided buffer */ [ computation ] /* data to be written now in driver-provided buffer */ /* flush write buffers and writeback, copy to bounce */ bus_dmamap_sync(..., BUS_DMASYNC_PREWRITE); [ do write DMA ] /* probably a no-op, but provided for consistency */ bus_dmamap_sync(..., BUS_DMASYNC_POSTWRITE); } bus_dmamap_unload(...); This function must be called to synchronize DMA buffers before and after a DMA operation. Other bus_dma functions can not be relied on to do this synchronization implicitly. If DMA read and write operations are not preceded and followed by the appro- priate synchronization operations, behavior is undefined. Behavior is not defined if invalid arguments are passed to bus_dmamap_sync(). If given valid arguments, bus_dmamap_sync() always succeeds. bus_dmamem_alloc(tag, size, alignment, boundary, segs, ...) Allocates memory that is "DMA safe" for the bus corresponding to the given tag. The mapping of this memory is machine-dependent (or "opaque"); machine-independent code is not to assume that the addresses returned are valid in kernel virtual address space, or that the addresses returned are system physical addresses. The address value returned as part of segs can thus not be used to program DMA controller address registers. Only the values in the dm_segs array of a successfully loaded DMA map (using bus_dmamap_load()) can be used for this purpose. Allocations will always be rounded to the hardware page size. Callers may wish to take advantage of this, and cluster alloca- tion of small data structures. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. size The amount of memory to allocate. alignment Each segment in the allocated memory will be aligned to this value. If the alignment is less than a hard- ware page size, it will be rounded up to the hardware page size. This value must be a power of two. boundary Each segment in the allocated memory must not cross this boundary (relative to zero). This value must be a power of two. A boundary value less than the size of the allocation is invalid. segs An array of bus_dma_segment_t's, filled in as memory is allocated, representing the opaque addresses of the memory chunks. nsegs Specifies the number of segments in segs, and this is the maximum number of segments that the allocated memory may contain. rsegs Used to return the actual number of segments the mem- ory contains. flags Flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. BUS_DMA_STREAMING Adjusts, if necessary, the size, alignment, and boundary constrains to conform to the platform-depen- dent requirements for the use of the BUS_DMA_STREAMING flag with the bus_dmamap_load() function. If the platform does not support the BUS_DMA_STREAMING feature, or if the size, alignment, and bound- ary constraints would already sat- isfy the platform's requirements, this flag is silently ignored. The BUS_DMA_STREAMING flag will never relax the constraints speci- fied in the call. BUS_DMA_BUS[1-4] These flags are placeholders, and may be used by busses to provide bus-dependent functionality. All pages allocated by bus_dmamem_alloc() will be wired down until they are freed by bus_dmamem_free(). Behavior is undefined if invalid arguments are passed to bus_dmamem_alloc(). Returns 0 on success, or an error code indicating mode of fail- ure. bus_dmamem_free(tag, segs, nsegs) Frees memory previously allocated by bus_dmamem_alloc(). Any mappings will be invalidated. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. segs The array of bus_dma_segment_t's filled in by bus_dmamem_alloc(). nsegs The number of segments in segs. Behavior is undefined if invalid arguments are passed to bus_dmamem_free(). If given valid arguments, bus_dmamem_free() always succeeds. bus_dmamem_map(tag, segs, nsegs, size, kvap, flags) Maps memory allocated with bus_dmamem_alloc() into kernel vir- tual address space. Arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. segs The array of bus_dma_segment_t's filled in by bus_dmamem_alloc(), representing the memory regions to map. nsegs The number of segments in segs. size The size of the mapping. kvap Filled in to specify the kernel virtual address where the memory is mapped. flags Flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. BUS_DMA_BUS[1-4] These flags are placeholders, and may be used by busses to provide bus-depen- dent functionality. BUS_DMA_COHERENT This flag is a hint to machine-depen- dent code. If possible, map the memory in such a way as it will be DMA coher- ent. This may include mapping the pages into uncached address space or setting the cache-inhibit bits in page table entries. If DMA coherent map- pings are impossible, this flag is silently ignored. Later, when this memory is loaded into a DMA map, machine-dependent code will take whatever steps are necessary to determine if the memory was mapped in a DMA coherent fashion. This may include checking if the kernel virtual address lies within uncached address space or if the cache-inhibit bits are set in page table entries. If it is deter- mined that the mapping is DMA coherent, state may be placed into the DMA map for use by later calls to bus_dmamap_sync(). Note that a device driver must not rely on BUS_DMA_COHERENT for correct opera- tion. All calls to bus_dmamap_sync() must still be made. This flag is pro- vided only as an optimization hint to machine-dependent code. Also note that this flag only applies to coherency between the CPU and mem- ory. Coherency between memory and the device is controlled with a different flag. See the description of the bus_dmamap_load() function. BUS_DMA_NOCACHE This flag is a hint to machine-depen- dent code. If possible, map the uncached memory. This flag may be use- ful in the case that the memory cache causes unexpected behavior of the device. Behavior is undefined if invalid arguments are passed to bus_dmamem_map(). Returns 0 on success, or an error code indicating mode of fail- ure. bus_dmamem_unmap(tag, kva, size) Unmaps memory previously mapped with bus_dmamem_map(), freeing the kernel virtual address space used by the mapping. The argu- ments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. kva The kernel virtual address of the mapped memory. size The size of the mapping. Behavior is undefined if invalid arguments are passed to bus_dmamem_unmap(). If given valid arguments, bus_dmamem_unmap() always succeeds. bus_dmamem_mmap(tag, segs, nsegs, off, prot, flags) Provides support for user mmap(2)'ing of DMA-safe memory. This function is to be called by a device driver's (*d_mmap)() entry point, which is called by the device pager for each page to be mapped. The arguments are as follows: tag This is the bus_dma_tag_t passed down from the parent driver via <bus>_attach_args. segs The array of bus_dma_segment_t's filled in by bus_dmamem_alloc(), representing the memory to be mmap(2)'ed. nsegs The number of elements in the segs array. off The offset of the page in DMA memory which is to be mapped. prot The protection codes for the mapping. flags Flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. BUS_DMA_BUS[1-4] These flags are placeholders, and may be used by busses to provide bus-depen- dent functionality. BUS_DMA_COHERENT See bus_dmamem_map() above for a description of this flag. BUS_DMA_NOCACHE See bus_dmamem_map() above for a description of this flag. Behavior is undefined if invalid arguments are passed to bus_dmamem_mmap(). Returns -1 to indicate failure. Otherwise, returns an opaque value to be interpreted by the device pager. bus_dmatag_subregion(tag, min_addr, max_addr, newtag, flags) Given a bus_dma_tag_t create a new bus_dma_tag_t with a limited bus address space. This function should not normally be used, but is useful for devices that do not support the full address space of the parent bus. The arguments are as follows: tag This is the bus_dma_tag_t to subregion. min_addr The smallest address this new tag can address. max_addr. The largest address this new tag can address. newtag Pointer filled in with the address of the new bus_dma_tag_t. flags Flags are defined as follows: BUS_DMA_WAITOK It is safe to wait (sleep) for resources during this call. BUS_DMA_NOWAIT It is not safe to wait (sleep) for resources during this call. bus_dmatag_destroy(tag) Free a tag created by bus_dmatag_subregion().
SEE ALSO
bus_space(9), mb(9) Jason Thorpe, "A Machine-Independent DMA Framework for NetBSD", Proceedings of the FREENIX track: 1998 USENIX Annual Technical Conference, pp. 1-12, 1998.
HISTORY
The bus_dma interface appeared in NetBSD 1.3.
AUTHORS
The bus_dma interface was designed and implemented by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, NASA Ames Research Center. Additional input on the bus_dma design was provided by Chris Demetriou, Charles Hannum, Ross Harvey, Matthew Jacob, Jonathan Stone, and Matt Thomas. NetBSD 5.1.2 February 19, 2009 NetBSD 5.1.2

Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.