spp(4) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
SPP(4)                  NetBSD Kernel Interfaces Manual                 SPP(4)


NAME

     spp -- Xerox Sequenced Packet Protocol


SYNOPSIS

     #include <sys/socket.h>
     #include <netns/ns.h>
     #include <netns/sp.h>

     int
     socket(AF_NS, SOCK_STREAM, 0);

     int
     socket(AF_NS, SOCK_SEQPACKET, 0);


DESCRIPTION

     The SPP protocol provides reliable, flow-controlled, two-way transmission
     of data.  It is a byte-stream protocol used to support the SOCK_STREAM
     abstraction.  SPP uses the standard NS(tm) address formats.

     Sockets using the SPP protocol are either ``active'' or ``passive''.
     Active sockets initiate connections to passive sockets.  By default SPP
     sockets are created active; to create a passive socket the listen(2) sys-
     tem call must be used after binding the socket with the bind(2) system
     call.  Only passive sockets may use the accept(2) call to accept incoming
     connections.  Only active sockets may use the connect(2) call to initiate
     connections.

     Passive sockets may ``underspecify'' their location to match incoming
     connection requests from multiple networks.  This technique, termed
     ``wildcard addressing'', allows a single server to provide service to
     clients on multiple networks.  To create a socket which listens on all
     networks, the NS address of all zeroes must be bound.  The SPP port may
     still be specified at this time; if the port is not specified the system
     will assign one.  Once a connection has been established the socket's
     address is fixed by the peer entity's location.   The address assigned
     the socket is the address associated with the network interface through
     which packets are being transmitted and received.  Normally this address
     corresponds to the peer entity's network.

     If the SOCK_SEQPACKET socket type is specified, each packet received has
     the actual 12 byte sequenced packet header left for the user to inspect:

           struct sphdr {
                   u_char          sp_cc;  /* connection control */
           #define SP_EM   0x10            /* end of message */
                   u_char          sp_dt;  /* datastream type */
                   u_short         sp_sid;
                   u_short         sp_did;
                   u_short         sp_seq;
                   u_short         sp_ack;
                   u_short         sp_alo;
           };

     This facilitates the implementation of higher level Xerox protocols which
     make use of the data stream type field and the end of message bit.  Con-
     versely, the user is required to supply a 12 byte header, the only part
     of which inspected is the data stream type and end of message fields.

     For either socket type, packets received with the Attention bit sent are
     interpreted as out of band data.  Data sent with ``send(..., ..., ...,
     MSG_OOB'') cause the attention bit to be set.


DIAGNOSTICS

     A socket operation may fail with one of the following errors returned:

     [EISCONN]        when trying to establish a connection on a socket which
                      already has one;

     [ENOBUFS]        when the system runs out of memory for an internal data
                      structure;

     [ETIMEDOUT]      when a connection was dropped due to excessive retrans-
                      missions;

     [ECONNRESET]     when the remote peer forces the connection to be closed;

     [ECONNREFUSED]   when the remote peer actively refuses connection estab-
                      lishment (usually because no process is listening to the
                      port);

     [EADDRINUSE]     when an attempt is made to create a socket with a port
                      which has already been allocated;

     [EADDRNOTAVAIL]  when an attempt is made to create a socket with a net-
                      work address for which no network interface exists.


SOCKET OPTIONS

     SO_DEFAULT_HEADERS  when set, this determines the data stream type and
                         whether the end of message bit is to be set on every
                         ensuing packet.

     SO_MTU              This specifies the maximum amount of user data in a
                         single packet.  The default is 576 bytes -
                         sizeof(struct spidp).  This quantity affects window-
                         ing - increasing it without increasing the amount of
                         buffering in the socket will lower the number of
                         unread packets accepted.  Anything larger than the
                         default will not be forwarded by a bona fide XEROX
                         product internetwork router.  The data argument for
                         the setsockopt call must be an unsigned short.


SEE ALSO

     intro(4), ns(4)


HISTORY

     The spp protocol appeared in 4.3BSD.


BUGS

     There should be some way to reflect record boundaries in a stream.  For
     stream mode, there should be an option to get the data stream type of the
     record the user process is about to receive.

NetBSD 3.0.1                    April 19, 1994                    NetBSD 3.0.1