scp(1) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
SCP(1)                  NetBSD General Commands Manual                  SCP(1)


NAME

     scp -- secure copy (remote file copy program)


SYNOPSIS

     scp [-1246BCpqrv] [-c cipher] [-F ssh_config] [-i identity_file]
         [-l limit] [-o ssh_option] [-P port] [-S program]
         [[user@]host1:]file1 [...] [[user@]host2:]file2


DESCRIPTION

     scp copies files between hosts on a network.  It uses ssh(1) for data
     transfer, and uses the same authentication and provides the same security
     as ssh(1).  Unlike rcp(1), scp will ask for passwords or passphrases if
     they are needed for authentication.

     Any file name may contain a host and user specification to indicate that
     the file is to be copied to/from that host.  Copies between two remote
     hosts are permitted.

     The options are as follows:

     -1      Forces scp to use protocol 1.

     -2      Forces scp to use protocol 2.

     -4      Forces scp to use IPv4 addresses only.

     -6      Forces scp to use IPv6 addresses only.

     -B      Selects batch mode (prevents asking for passwords or
             passphrases).

     -C      Compression enable.  Passes the -C flag to ssh(1) to enable com-
             pression.

     -c cipher
             Selects the cipher to use for encrypting the data transfer.  This
             option is directly passed to ssh(1).

     -F ssh_config
             Specifies an alternative per-user configuration file for ssh.
             This option is directly passed to ssh(1).

     -i identity_file
             Selects the file from which the identity (private key) for RSA
             authentication is read.  This option is directly passed to
             ssh(1).

     -l limit
             Limits the used bandwidth, specified in Kbit/s.

     -o ssh_option
             Can be used to pass options to ssh in the format used in
             ssh_config(5).  This is useful for specifying options for which
             there is no separate scp command-line flag.  For full details of
             the options listed below, and their possible values, see
             ssh_config(5).

                   AddressFamily
                   BatchMode
                   BindAddress
                   ChallengeResponseAuthentication
                   CheckHostIP
                   Cipher
                   Ciphers
                   Compression
                   CompressionLevel
                   ConnectionAttempts
                   ConnectTimeout
                   ControlMaster
                   ControlPath
                   GlobalKnownHostsFile
                   GSSAPIAuthentication
                   GSSAPIDelegateCredentials
                   Host
                   HostbasedAuthentication
                   HostKeyAlgorithms
                   HostKeyAlias
                   HostName
                   IdentityFile
                   IdentitiesOnly
                   LogLevel
                   MACs
                   NoHostAuthenticationForLocalhost
                   NumberOfPasswordPrompts
                   PasswordAuthentication
                   Port
                   PreferredAuthentications
                   Protocol
                   ProxyCommand
                   PubkeyAuthentication
                   RhostsRSAAuthentication
                   RSAAuthentication
                   SendEnv
                   ServerAliveInterval
                   ServerAliveCountMax
                   SmartcardDevice
                   StrictHostKeyChecking
                   TCPKeepAlive
                   UsePrivilegedPort
                   User
                   UserKnownHostsFile
                   VerifyHostKeyDNS

     -P port
             Specifies the port to connect to on the remote host.  Note that
             this option is written with a capital `P', because -p is already
             reserved for preserving the times and modes of the file in
             rcp(1).

     -p      Preserves modification times, access times, and modes from the
             original file.

     -q      Disables the progress meter.

     -r      Recursively copy entire directories.

     -S program
             Name of program to use for the encrypted connection.  The program
             must understand ssh(1) options.

     -v      Verbose mode.  Causes scp and ssh(1) to print debugging messages
             about their progress.  This is helpful in debugging connection,
             authentication, and configuration problems.


DIAGNOSTICS

     scp exits with 0 on success or >0 if an error occurred.


SEE ALSO

     rcp(1), sftp(1), ssh(1), ssh-add(1), ssh-agent(1), ssh-keygen(1),
     ssh_config(5), sshd(8)


HISTORY

     scp is based on the rcp(1) program in BSD source code from the Regents of
     the University of California.


AUTHORS

     Timo Rinne <tri@iki.fi>
     Tatu Ylonen <ylo@cs.hut.fi>

NetBSD 3.0.1                  September 25, 1999                  NetBSD 3.0.1