STF(4) NetBSD Kernel Interfaces Manual STF(4)
NAME
stf - 6to4 tunnel interface
SYNOPSIS
pseudo-device stf
DESCRIPTION
The stf interface supports ``6to4'' IPv6 in IPv4 encapsulation. It can tunnel IPv6 traffic over IPv4, as specified in RFC3056. stf interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands. Only one stf interface may be created. For ordinary nodes in 6to4 sites, you do not need a stf interface. The stf interface is only necessary on the site border router (called the ``6to4 router'' in the specification). Due to the way the 6to4 protocol is specified, stf interfaces require certain configuration to work properly. A single (no more than one) valid 6to4 address needs to be configured on the interface. ``A valid 6to4 address'' is an address which has the following properties. If any of the following properties are not satisfied, stf raises a runtime error on packet transmission. Read the specification for more details. · matches 2002:xxyy:zzuu::/48, where xxyy:zzuu is the hexadecimal nota- tion of an IPv4 address for the node. The IPv4 address used can be taken from any interface your node has. Since the specification for- bids the use of IPv4 private address, the address needs to be a global IPv4 address. · Subnet identifier portion (48th to 63rd bit) and interface identifier portion (lower 64 bits) are properly filled to avoid address colli- sions. If you would like the node to behave as a relay router, the prefix length for the IPv6 interface address needs to be 16 so that the node would con- sider any 6to4 destination as ``on-link''. If you would like to restrict 6to4 peers to be inside a certain IPv4 prefix, you may want to configure the IPv6 prefix length to be ``16 + IPv4 prefix length''. The stf inter- face will check the IPv4 source address on packets if the IPv6 prefix length is larger than 16. stf can be configured to be ECN (Explicit Congestion Notification) friendly. This can be configured by IFF_LINK1. See gif(4) for details. Please note that the 6to4 specification is written as an ``accept tunnelled packet from everyone'' tunnelling device. By enabling the stf device, you are making it much easier for malicious parties to inject fabricated IPv6 packets to your node. Also, malicious parties can inject IPv6 packets with fabricated source addresses to make your node generate improper tunnelled packets. Administrators must be cautious when enabling the interface. To prevent possible attacks, the stf interface filters out the following packets (note that the checks are in no way complete): · Packets with IPv4 unspecified addresses as outer IPv4 source/destina- tion (0.0.0.0/8) · Packets with the loopback address as outer IPv4 source/destination (127.0.0.0/8) · Packets with IPv4 multicast addresses as outer IPv4 source/destina- tion (224.0.0.0/4) · Packets with limited broadcast addresses as outer IPv4 source/desti- nation (255.0.0.0/8) · Packets with private addresses as outer IPv4 source/destination (10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16) · Packets with IPv4 link-local addresses as outer IPv4 source/destina- tion (169.254.0.0/16) · Packets with subnet broadcast addresses as outer IPv4 source/destina- tion. The check is made against subnet broadcast addresses for all of the directly connected subnets. · Packets that do not pass ingress filtering. Outer IPv4 source addresses must meet the IPv4 topology on the routing table. Ingress filtering can be turned off by IFF_LINK2 bit. · The same set of rules are applied against the IPv4 address embedded into the inner IPv6 address, if the IPv6 address matches the 6to4 prefix. · Packets with site-local or link-local unicast addresses as inner IPv6 source/destination · Packets with node-local or link-local multicast addresses as inner IPv6 source/destination It is recommended to filter/audit incoming IPv4 packets with IP protocol number 41, as necessary. It is also recommended to filter/audit encapsu- lated IPv6 packets as well. You may also want to run normal ingress fil- tering against inner IPv6 addresses to avoid spoofing. By setting the IFF_LINK0 flag on the stf interface, it is possible to disable the input path, making direct attacks from the outside impossi- ble. Note, however, that other security risks exist. If you wish to use the configuration, you must not advertise your 6to4 addresses to others.
EXAMPLES
Note that 8504:0506 is equal to 133.4.5.6, written in hexadecimal. # ifconfig ne0 inet 133.4.5.6 netmask 0xffffff00 # ifconfig stf0 create inet6 2002:8504:0506:0000:a00:5aff:fe38:6f86 \ prefixlen 16 alias The following configuration accepts packets from IPv4 source address 9.1.0.0/16 only. It emits 6to4 packets only for IPv6 destination 2002:0901::/32 (IPv4 destination will match 9.1.0.0/16). # ifconfig ne0 inet 9.1.2.3 netmask 0xffff0000 # ifconfig stf0 create inet6 2002:0901:0203:0000:a00:5aff:fe38:6f86 \ prefixlen 32 alias The following configuration uses the stf interface as an output-only device. You need to have alternative IPv6 connectivity (other than 6to4) to use this configuration. For outbound traffic, you can reach other 6to4 networks efficiently via stf. For inbound traffic, you will not receive any 6to4-tunneled packets (less security drawbacks). Be careful not to advertise your 6to4 prefix to others (2002:8504:0506::/48), and not to use your 6to4 prefix as a source address. # ifconfig ne0 inet 133.4.5.6 netmask 0xffffff00 # ifconfig stf0 create inet6 2002:8504:0506:0000:a00:5aff:fe38:6f86 \ prefixlen 16 alias deprecated link0 # route add -inet6 2002:: -prefixlen 16 ::1 -ifp stf0
SEE ALSO
gif(4), inet(4), inet6(4) http://www.6bone.net/6bone_6to4.html Brian Carpenter and Keith Moore, Connection of IPv6 Domains via IPv4 Clouds, RFC, 3056, February 2001. F. Baker and P. Savola, Ingress Filtering for Multihomed Networks, RFC, 3704, March 2004. Jun-ichiro itojun Hagino, Possible abuse against IPv6 transition technologies, draft-itojun-ipv6-transition-abuse-01.txt, July 2000, work in progress.
HISTORY
The stf device first appeared in WIDE/KAME IPv6 stack.
BUGS
No more than one stf interface is allowed for a node, and no more than one IPv6 interface address is allowed for an stf interface. This is to avoid source address selection conflicts between the IPv6 layer and the IPv4 layer, and to cope with ingress filtering rules on the other side. This is a feature to make stf work right for all occasions. NetBSD 2.1 March 24, 2004 NetBSD 2.1
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.