tun(4) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
TUN(4)                    NetBSD Programmer's Manual                    TUN(4)


NAME

     tun - tunnel software network interface


SYNOPSIS

     pseudo-device tun [count]


DESCRIPTION

     The tun interface is a software loopback mechanism that can be loosely
     described as the network interface analog of the pty(4), that is, tun
     does for network interfaces what the pty driver does for terminals.

     The tun driver, like the pty driver, provides two interfaces: an inter-
     face like the usual facility it is simulating (a network interface in the
     case of tun, or a terminal for pty), and a character-special device
     ``control'' interface.

     To use a tun device, the administrator must first create the interface.
     This can be done by using the ifconfig(8) `create' command, or via the
     SIOCIFCREATE ioctl.  Note that an open() call on /dev/tunN, will indicate
     that the device is not configured (ENXIO) unless the corresponding net-
     work interface has been created.

     The network interfaces are named tun0, tun1, etc, as many in all as the
     count figure given on the pseudo-device line.  Each one supports the usu-
     al network-interface ioctl(2)s, such as SIOCSIFADDR and SIOCSIFNETMASK,
     and thus can be used with ifconfig(8) like any other interface.  At boot
     time, they are POINTOPOINT interfaces, but this can be changed; see the
     description of the control device, below.  When the system chooses to
     transmit a packet on the network interface, the packet can be read from
     the control device (it appears there as ``output''); writing a packet to
     the control device generates an input packet on the network interface, as
     if the (non-existent) hardware had just received it.

     The tunnel device, normally /dev/tunN, is exclusive-open (it cannot be
     opened if it is already open) and is restricted to the super-user
     (regardless of file system permissions). A read() call will return an er-
     ror (EHOSTDOWN) if the interface is not ``ready'' (which means that the
     interface address has not been set).  Once the interface is ready, read()
     will return a packet if one is available; if not, it will either block
     until one is or return EAGAIN, depending on whether non-blocking I/O has
     been enabled.  If the packet is longer than is allowed for in the buffer
     passed to read(), the extra data will be silently dropped.

     Packets can be optionally prepended with the destination address as pre-
     sented to the network interface output routine (`tunoutput').  The desti-
     nation address is in `struct sockaddr' format. The actual length of the
     prepended address is in the member `sa_len'.  The packet data follows im-
     mediately.  A write(2) call passes a packet in to be ``received'' on the
     pseudo-interface.  Each write() call supplies exactly one packet; the
     packet length is taken from the amount of data provided to write().
     Writes will not block; if the packet cannot be accepted for a transient
     reason (e.g., no buffer space available), it is silently dropped; if the
     reason is not transient (e.g., packet too large), an error is returned.
     If ``link-layer mode'' is on (see TUNSLMODE below), the actual packet da-
     ta must be preceded by a `struct sockaddr'.  The driver currently only
     inspects the `sa_family' field.  The following ioctl(2) calls are sup-
     ported (defined in <net/if_tun.h>):

     TUNSDEBUG   The argument should be a pointer to an int; this sets the in-
                 ternal debugging variable to that value.  What, if anything,
                 this variable controls is not documented here; see the source
                 code.

     TUNGDEBUG   The argument should be a pointer to an int; this stores the
                 internal debugging variable's value into it.

     TUNSIFMODE  The argument should be a pointer to an int; its value must be
                 either IFF_POINTOPOINT or IFF_BROADCAST (optionally
                 IFF_MULTICAST may be or'ed into the value).  The type of the
                 corresponding tunn interface is set to the supplied type.  If
                 the value is anything else, an EINVAL error occurs.  The in-
                 terface must be down at the time; if it is up, an EBUSY error
                 occurs.

     TUNSLMODE   The argument should be a pointer to an int; a non-zero value
                 turns on ``link-layer'' mode, causing packets read from the
                 tunnel device to be prepended with network destination ad-
                 dress.

     FIONBIO     Turn non-blocking I/O for reads off or on, according as the
                 argument int's value is or isn't zero (Writes are always
                 nonblocking).

     FIOASYNC    Turn asynchronous I/O for reads (i.e., generation of SIGIO
                 when data is available to be read) off or on, according as
                 the argument int's value is or isn't zero.

     FIONREAD    If any packets are queued to be read, store the size of the
                 first one into the argument int; otherwise, store zero.

     TIOCSPGRP   Set the process group to receive SIGIO signals, when asyn-
                 chronous I/O is enabled, to the argument int value.

     TIOCGPGRP   Retrieve the process group value for SIGIO signals into the
                 argument int value.

     The control device also supports select(2) for read; selecting for write
     is pointless, and always succeeds, since writes are always non-blocking.

     On the last close of the data device, by default, the interface is
     brought down (as if with``ifconfig tunn down'').  All queued packets are
     thrown away.  If the interface is up when the data device is not open
     output packets are always thrown away rather than letting them pile up.


SEE ALSO

     inet(4), intro(4)


BUGS

     Currently is IPv4-only.

NetBSD 1.6.2                    March 10, 1996                               2