- NetBSD Manual Pages
NDP(8) NetBSD System Manager's Manual NDP(8)
Powered by man-cgi (2021-06-01).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
ndp -- control/diagnose IPv6 neighbor discovery protocol
ndp [-nt] hostname
ndp [-nt] -a | -c | -p
ndp [-nt] -r
ndp [-nt] -H | -P | -R
ndp [-nt] -A wait
ndp [-nt] -d hostname
ndp [-nt] -f filename
ndp [-nt] -i interface [expressions ...]
ndp [-nt] -I [interface | delete]
ndp [-nt] -s nodename etheraddr [temp] [proxy]
The ndp command manipulates the address mapping table used by the Neigh-
bor Discovery Protocol (NDP).
Repeat -a (dump NDP entries) every wait seconds.
-a Dump the currently existing NDP entries. The following informa-
tion will be printed:
Neighbor IPv6 address of the neighbor.
Linklayer address of the neighbor. It could be
``(incomplete)'' when the address is not available.
Netif Network interface associated with the neighbor cache
Expire The time until expiry of the entry. The entry could
become ``permanent'', in which case it will never
S State of the neighbor cache entry, as a single let-
? Unknown state (should never happen).
Flags Flags on the neighbor cache entry, in a single let-
ter. They are: Router, proxy neighbor advertisement
(``p''). The field could be followed by a decimal
number, which means the number of NS probes the node
has sent during the current state.
-c Erase all the NDP entries.
-d Delete specified NDP entry.
-f Parse the file specified by filename.
-H Harmonize consistency between the routing table and the default
router list; install the top entry of the list into the kernel
-I Shows the default interface used as the default route when there
is no default router.
Specifies the default interface to be used when there is no
interface specified even though required.
The current default interface will be deleted from the kernel.
-i interface [expressions ...]
View ND information for the specified interface. If additional
arguments expressions are given, ndp sets or clears the flags or
variables for the interface as specified in the expression. Each
expression should be separated by white spaces or tab characters.
Possible expressions are as follows. Some of the expressions can
begin with the special character `-', which means the flag speci-
fied in the expression should be cleared. Note that you need --
before -foo in this case.
nud Turn on or off NUD (Neighbor Unreachability Detection) on
the interface. NUD is usually turned on by default.
Specify whether or not to accept Router Advertisement
messages received on the interface. Note that the kernel
does not accept Router Advertisement messages, even if
the flag accept_rtadv is on, unless either the
net.inet6.ip6.accept_rtadv variable is non-0, or the flag
override_rtadv is on. This flag is set to 1 by default.
Specify whether or not to perform automatic link-local
address configuration on interface. This flag is set by
net.inet6.ip6.auto_linklocal sysctl variable.
Specify whether or not to override the
net.inet6.ip6.accept_rtadv variable. If the flag is on,
then it will suffice to set the flag accept_rtadv to make
the kernel accept Router Advertisement messages on the
interface. This flag is set to 0 by default.
Prefer addresses on the interface as candidates of the
source address for outgoing packets. The default value
of this flag is off. For more details about the entire
algorithm of source address selection, see the
IMPLEMENTATION file supplied with the KAME kit.
Disable IPv6 operation on the interface. When disabled,
the interface discards any IPv6 packets received on or
being sent to the interface and any IPv6 addresses on the
interface are marked as ``tentative''. When the disabled
flag is cleared, DAD will be performed. In the sending
case, an error of ENETDOWN will be returned to the appli-
cation. This flag is typically set automatically in the
kernel as a result of a certain failure of Duplicate
Address Detection. While the flag can be set or cleared
by hand with the ndp command, it is not generally advis-
able to modify this flag manually.
Specify the BaseReachbleTimer on the interface in mil-
Specify the RetransTimer on the interface in millisecond.
Specify the Cur Hop Limit on the interface.
-n Do not try to resolve numeric addresses to hostnames.
-P Flush all the entries in the prefix list.
-p Show prefix list.
-R Flush all the entries in the default router list.
-r Show default router list.
-s Register an NDP entry for a node. The entry will be permanent
unless the word temp is given in the command. If the word proxy
is given, this system will act as a proxy NDP server, responding
to requests for hostname even though the host address is not its
-t Print timestamp on each entry, making it possible to merge output
with tcpdump(8). Most useful when used with -A.
The ndp command will exit with 0 on success, and non-zero on errors.
The ndp command first appeared in the WIDE Hydrangea IPv6 protocol stack
NetBSD 9.2 February 14, 2018 NetBSD 9.2