boot(8)
- NetBSD Manual Pages
BOOT(8) NetBSD/sun2 System Manager's Manual BOOT(8)
NAME
boot -- system bootstrapping procedures
SYNOPSIS
b [dev [(cntrl, unit, part)]] [file] [-adqsv]
DESCRIPTION
Power fail and crash recovery
Normally, the system will reboot itself at power-up or after crashes. An
automatic consistency check of the file systems will be performed as
described in fsck(8), and unless this fails, the system will resume
multi-user operations.
Selecting the device and kernel to boot
Normally, the b command alone is sufficient to boot the system, as the
PROM chooses a default boot device dev if none is specified. The PROM
chooses the first device present on the system from the following ordered
list:
sd SCSI disk
ie Intel Ethernet
ec 3Com Ethernet
Unless specified, the controller number cntrl, unit number unit, and par-
tition number part default to zero, which is almost always correct.
The controller number can be specified if there is more than one of the
given device in the system. For example, use ``ie(1,,)'' to boot off of
the second Intel Ethernet in the system.
The unit number specifies one of the many devices attached to a con-
troller. The exact meaning and values vary depending on the device name.
For example, ``sd(,18,)'' boots the disk at target 6 on the first SCSI
controller, 18 being the target number 6, multiplied by 4, and given in
hexadecimal.
The partition number specifies one of the many partitions on a device.
The exact meaning and values vary depending on the device name. For
example, ``sd(,18,1)'' boots the second partition on the disk at target 6
on the first SCSI controller.
The PROM only loads a first-stage boot program, currently either
/usr/mdec/bootxx (for a disk boot), or /usr/mdec/bootyy (for a network
boot). This first-stage boot program then loads the second-stage boot
program from the same device, currently either /usr/mdec/ufsboot (for a
disk boot), or /usr/mdec/netboot (for a network boot).
The second-stage boot program will then attempt to load the kernel named
file (or vmunix if none is specified). The second-stage disk boot pro-
gram /usr/mdec/ufsboot loads the kernel from the same device that it was
loaded from, while the second-stage network boot program
/usr/mdec/netboot will load the kernel from the NFS root as determined by
the procedure described in diskless(8).
Boot program options
-a Prompt for the root file system device, the system crash dump
device, and the path to init(8).
-d Bring the system up in debug mode. Here it waits for a kernel
debugger connect; see ddb(4).
-q Boot the system in quiet mode.
-s Bring the system up in single-user mode.
-v Boot the system in verbose mode.
Other flags are currently ignored.
At any time you can break back to the ROM by pressing the `L1' and `a'
keys at the same time (if the console is a serial port the same is
achieved by sending a `break'). If you do this accidentally you can con-
tinue whatever was in progress by typing `c' followed by the return key.
FILES
/netbsd system code
/usr/mdec/bootxx first-level boot block for disks
/usr/mdec/bootyy first-level boot block for NFS (diskless) boot
/usr/mdec/netboot boot program for NFS (diskless) boot
/usr/mdec/ufsboot second-level boot program for UFS disks
/usr/sbin/installboot program to install bootxx on a disk
SEE ALSO
crash(8), disklabel(8), fsck(8), halt(8), init(8), rc(8), shutdown(8),
syslogd(8)
NetBSD 7.1_STABLE April 29, 2003 NetBSD 7.1_STABLE
Powered by man-cgi (2024-03-20).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.