SSH_CONFIG(5) NetBSD File Formats Manual SSH_CONFIG(5)
NAME
ssh_config -- OpenSSH SSH client configuration files
SYNOPSIS
~/.ssh/config /etc/ssh/ssh_config
DESCRIPTION
ssh(1) obtains configuration data from the following sources in the fol- lowing order: 1. command-line options 2. user's configuration file (~/.ssh/config) 3. system-wide configuration file (/etc/ssh/ssh_config) For each parameter, the first obtained value will be used. The configu- ration files contain sections separated by ``Host'' specifications, and that section is only applied for hosts that match one of the patterns given in the specification. The matched host name is usually the one given on the command line (see the CanonicalizeHostname option for excep- tions.) Since the first obtained value for each parameter is used, more host-spe- cific declarations should be given near the beginning of the file, and general defaults at the end. The configuration file has the following format: Empty lines and lines starting with `#' are comments. Otherwise a line is of the format ``keyword arguments''. Configuration options may be separated by whitespace or optional whitespace and exactly one `='; the latter format is useful to avoid the need to quote whitespace when speci- fying configuration options using the ssh, scp, and sftp -o option. Arguments may optionally be enclosed in double quotes (") in order to represent arguments containing spaces. The possible keywords and their meanings are as follows (note that key- words are case-insensitive and arguments are case-sensitive): Host Restricts the following declarations (up to the next Host or Match keyword) to be only for those hosts that match one of the patterns given after the keyword. If more than one pattern is provided, they should be separated by whitespace. A single `*' as a pattern can be used to provide global defaults for all hosts. The host is usually the hostname argument given on the command line (see the CanonicalizeHostname option for excep- tions.) A pattern entry may be negated by prefixing it with an exclama- tion mark (`!'). If a negated entry is matched, then the Host entry is ignored, regardless of whether any other patterns on the line match. Negated matches are therefore useful to provide exceptions for wildcard matches. See PATTERNS for more information on patterns. Match Restricts the following declarations (up to the next Host or Match keyword) to be used only when the conditions following the Match keyword are satisfied. Match conditions are specified using one or more critera or the single token all which always matches. The available criteria keywords are: canonical, exec, host, originalhost, user, and localuser. The all criteria must appear alone or immediately after canonical. Other criteria may be combined arbitrarily. All criteria but all and canonical require an argument. Criteria may be negated by prepending an exclamation mark (`!'). The canonical keywork matches only when the configuration file is being re-parsed after hostname canonicalization (see the CanonicalizeHostname option.) This may be useful to specify con- ditions that work with canonical host names only. The exec key- word executes the specified command under the user's shell. If the command returns a zero exit status then the condition is con- sidered true. Commands containing whitespace characters must be quoted. The following character sequences in the command will be expanded prior to execution: `%L' will be substituted by the first component of the local host name, `%l' will be substituted by the local host name (including any domain name), `%h' will be substituted by the target host name, `%n' will be substituted by the original target host name specified on the command-line, `%p' the destination port, `%r' by the remote login username, and `%u' by the username of the user running ssh(1). The other keywords' criteria must be single entries or comma-sep- arated lists and may use the wildcard and negation operators described in the PATTERNS section. The criteria for the host keyword are matched against the target hostname, after any sub- stitution by the Hostname or CanonicalizeHostname options. The originalhost keyword matches against the hostname as it was spec- ified on the command-line. The user keyword matches against the target username on the remote host. The localuser keyword matches against the name of the local user running ssh(1) (this keyword may be useful in system-wide ssh_config files). AddressFamily Specifies which address family to use when connecting. Valid arguments are ``any'', ``inet'' (use IPv4 only), or ``inet6'' (use IPv6 only). BatchMode If set to ``yes'', passphrase/password querying will be disabled. This option is useful in scripts and other batch jobs where no user is present to supply the password. The argument must be ``yes'' or ``no''. The default is ``no''. BindAddress Use the specified address on the local machine as the source address of the connection. Only useful on systems with more than one address. Note that this option does not work if UsePrivilegedPort is set to ``yes''. CanonicalDomains When CanonicalizeHostname is enabled, this option specifies the list of domain suffixes in which to search for the specified des- tination host. CanonicalizeFallbackLocal Specifies whether to fail with an error when hostname canonical- ization fails. The default, ``yes'', will attempt to look up the unqualified hostname using the system resolver's search rules. A value of ``no'' will cause ssh(1) to fail instantly if CanonicalizeHostname is enabled and the target hostname cannot be found in any of the domains specified by CanonicalDomains. CanonicalizeHostname Controls whether explicit hostname canonicalization is performed. The default, ``no'', is not to perform any name rewriting and let the system resolver handle all hostname lookups. If set to ``yes'' then, for connections that do not use a ProxyCommand, ssh(1) will attempt to canonicalize the hostname specified on the command line using the CanonicalDomains suffixes and CanonicalizePermittedCNAMEs rules. If CanonicalizeHostname is set to ``always'', then canonicalization is applied to proxied connections too. If this option is enabled, then the configuration files are pro- cessed again using the new target name to pick up any new config- uration in matching Host and Match stanzas. CanonicalizeMaxDots Specifies the maximum number of dot characters in a hostname before canonicalization is disabled. The default, ``1'', allows a single dot (i.e. hostname.subdomain). CanonicalizePermittedCNAMEs Specifies rules to determine whether CNAMEs should be followed when canonicalizing hostnames. The rules consist of one or more arguments of source_domain_list:target_domain_list, where source_domain_list is a pattern-list of domains that may follow CNAMEs in canonicalization, and target_domain_list is a pattern- list of domains that they may resolve to. For example, ``*.a.example.com:*.b.example.com,*.c.example.com'' will allow hostnames matching ``*.a.example.com'' to be canoni- calized to names in the ``*.b.example.com'' or ``*.c.example.com'' domains. ChallengeResponseAuthentication Specifies whether to use challenge-response authentication. The argument to this keyword must be ``yes'' or ``no''. The default is ``yes''. CheckHostIP If this flag is set to ``yes'', ssh(1) will additionally check the host IP address in the known_hosts file. This allows ssh to detect if a host key changed due to DNS spoofing. If the option is set to ``no'', the check will not be executed. The default is ``yes''. Cipher Specifies the cipher to use for encrypting the session in proto- col version 1. Currently, ``blowfish'', ``3des'', and ``des'' are supported. des is only supported in the ssh(1) client for interoperability with legacy protocol 1 implementations that do not support the 3des cipher. Its use is strongly discouraged due to cryptographic weaknesses. The default is ``3des''. Ciphers Specifies the ciphers allowed for protocol version 2 in order of preference. Multiple ciphers must be comma-separated. The sup- ported ciphers are: 3des-cbc aes128-cbc aes192-cbc aes256-cbc aes128-ctr aes192-ctr aes256-ctr aes128-gcm@openssh.com aes256-gcm@openssh.com arcfour arcfour128 arcfour256 blowfish-cbc cast128-cbc chacha20-poly1305@openssh.com The default is: aes128-ctr,aes192-ctr,aes256-ctr, aes128-gcm@openssh.com,aes256-gcm@openssh.com, chacha20-poly1305@openssh.com, arcfour256,arcfour128, aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc, aes192-cbc,aes256-cbc,arcfour The list of available ciphers may also be obtained using the -Q option of ssh(1) with an argument of ``cipher''. ClearAllForwardings Specifies that all local, remote, and dynamic port forwardings specified in the configuration files or on the command line be cleared. This option is primarily useful when used from the ssh(1) command line to clear port forwardings set in configura- tion files, and is automatically set by scp(1) and sftp(1). The argument must be ``yes'' or ``no''. The default is ``no''. Compression Specifies whether to use compression. The argument must be ``yes'' or ``no''. The default is ``no''. CompressionLevel Specifies the compression level to use if compression is enabled. The argument must be an integer from 1 (fast) to 9 (slow, best). The default level is 6, which is good for most applications. The meaning of the values is the same as in gzip(1). Note that this option applies to protocol version 1 only. ConnectionAttempts Specifies the number of tries (one per second) to make before exiting. The argument must be an integer. This may be useful in scripts if the connection sometimes fails. The default is 1. ConnectTimeout Specifies the timeout (in seconds) used when connecting to the SSH server, instead of using the default system TCP timeout. This value is used only when the target is down or really unreachable, not when it refuses the connection. ControlMaster Enables the sharing of multiple sessions over a single network connection. When set to ``yes'', ssh(1) will listen for connec- tions on a control socket specified using the ControlPath argu- ment. Additional sessions can connect to this socket using the same ControlPath with ControlMaster set to ``no'' (the default). These sessions will try to reuse the master instance's network connection rather than initiating new ones, but will fall back to connecting normally if the control socket does not exist, or is not listening. Setting this to ``ask'' will cause ssh to listen for control con- nections, but require confirmation using the SSH_ASKPASS program before they are accepted (see ssh-add(1) for details). If the ControlPath cannot be opened, ssh will continue without connect- ing to a master instance. X11 and ssh-agent(1) forwarding is supported over these multi- plexed connections, however the display and agent forwarded will be the one belonging to the master connection i.e. it is not pos- sible to forward multiple displays or agents. Two additional options allow for opportunistic multiplexing: try to use a master connection but fall back to creating a new one if one does not already exist. These options are: ``auto'' and ``autoask''. The latter requires confirmation like the ``ask'' option. ControlPath Specify the path to the control socket used for connection shar- ing as described in the ControlMaster section above or the string ``none'' to disable connection sharing. In the path, `%L' will be substituted by the first component of the local host name, `%l' will be substituted by the local host name (including any domain name), `%h' will be substituted by the target host name, `%n' will be substituted by the original target host name speci- fied on the command line, `%p' the destination port, `%r' by the remote login username, `%u' by the username of the user running ssh(1), and `%C' by a hash of the concatenation: %l%h%p%r. It is recommended that any ControlPath used for opportunistic connec- tion sharing include at least %h, %p, and %r (or alternatively %C) and be placed in a directory that is not writable by other users. This ensures that shared connections are uniquely identi- fied. ControlPersist When used in conjunction with ControlMaster, specifies that the master connection should remain open in the background (waiting for future client connections) after the initial client connec- tion has been closed. If set to ``no'', then the master connec- tion will not be placed into the background, and will close as soon as the initial client connection is closed. If set to ``yes'' or ``0'', then the master connection will remain in the background indefinitely (until killed or closed via a mechanism such as the ssh(1) ``-O exit'' option). If set to a time in sec- onds, or a time in any of the formats documented in sshd_config(5), then the backgrounded master connection will automatically terminate after it has remained idle (with no client connections) for the specified time. DynamicForward Specifies that a TCP port on the local machine be forwarded over the secure channel, and the application protocol is then used to determine where to connect to from the remote machine. The argument must be [bind_address:]port. IPv6 addresses can be specified by enclosing addresses in square brackets. By default, the local port is bound in accordance with the GatewayPorts set- ting. However, an explicit bind_address may be used to bind the connection to a specific address. The bind_address of ``localhost'' indicates that the listening port be bound for local use only, while an empty address or `*' indicates that the port should be available from all interfaces. Currently the SOCKS4 and SOCKS5 protocols are supported, and ssh(1) will act as a SOCKS server. Multiple forwardings may be specified, and additional forwardings can be given on the command line. Only the superuser can forward privileged ports. EnableSSHKeysign Setting this option to ``yes'' in the global client configuration file /etc/ssh/ssh_config enables the use of the helper program ssh-keysign(8) during HostbasedAuthentication. The argument must be ``yes'' or ``no''. The default is ``no''. This option should be placed in the non-hostspecific section. See ssh-keysign(8) for more information. EscapeChar Sets the escape character (default: `~'). The escape character can also be set on the command line. The argument should be a single character, `^' followed by a letter, or ``none'' to dis- able the escape character entirely (making the connection trans- parent for binary data). ExitOnForwardFailure Specifies whether ssh(1) should terminate the connection if it cannot set up all requested dynamic, tunnel, local, and remote port forwardings. The argument must be ``yes'' or ``no''. The default is ``no''. FingerprintHash Specifies the hash algorithm used when displaying key finger- prints. Valid options are: ``md5'' and ``sha256''. The default is ``sha256''. ForwardAgent Specifies whether the connection to the authentication agent (if any) will be forwarded to the remote machine. The argument must be ``yes'' or ``no''. The default is ``no''. Agent forwarding should be enabled with caution. Users with the ability to bypass file permissions on the remote host (for the agent's Unix-domain socket) can access the local agent through the forwarded connection. An attacker cannot obtain key material from the agent, however they can perform operations on the keys that enable them to authenticate using the identities loaded into the agent. ForwardX11 Specifies whether X11 connections will be automatically redi- rected over the secure channel and DISPLAY set. The argument must be ``yes'' or ``no''. The default is ``no''. X11 forwarding should be enabled with caution. Users with the ability to bypass file permissions on the remote host (for the user's X11 authorization database) can access the local X11 dis- play through the forwarded connection. An attacker may then be able to perform activities such as keystroke monitoring if the ForwardX11Trusted option is also enabled. ForwardX11Timeout Specify a timeout for untrusted X11 forwarding using the format described in the TIME FORMATS section of sshd_config(5). X11 connections received by ssh(1) after this time will be refused. The default is to disable untrusted X11 forwarding after twenty minutes has elapsed. ForwardX11Trusted If this option is set to ``yes'', remote X11 clients will have full access to the original X11 display. If this option is set to ``no'', remote X11 clients will be con- sidered untrusted and prevented from stealing or tampering with data belonging to trusted X11 clients. Furthermore, the xauth(1) token used for the session will be set to expire after 20 min- utes. Remote clients will be refused access after this time. The default is ``no''. See the X11 SECURITY extension specification for full details on the restrictions imposed on untrusted clients. GatewayPorts Specifies whether remote hosts are allowed to connect to local forwarded ports. By default, ssh(1) binds local port forwardings to the loopback address. This prevents other remote hosts from connecting to forwarded ports. GatewayPorts can be used to spec- ify that ssh should bind local port forwardings to the wildcard address, thus allowing remote hosts to connect to forwarded ports. The argument must be ``yes'' or ``no''. The default is ``no''. GlobalKnownHostsFile Specifies one or more files to use for the global host key data- base, separated by whitespace. The default is /etc/ssh/ssh_known_hosts, /etc/ssh/ssh_known_hosts2. GSSAPIAuthentication Specifies whether user authentication based on GSSAPI is allowed. The default is ``no''. Note that this option applies to protocol version 2 only. GSSAPIDelegateCredentials Forward (delegate) credentials to the server. The default is ``no''. Note that this option applies to protocol version 2 only. HashKnownHosts Indicates that ssh(1) should hash host names and addresses when they are added to ~/.ssh/known_hosts. These hashed names may be used normally by ssh(1) and sshd(8), but they do not reveal iden- tifying information should the file's contents be disclosed. The default is ``no''. Note that existing names and addresses in known hosts files will not be converted automatically, but may be manually hashed using ssh-keygen(1). HostbasedAuthentication Specifies whether to try rhosts based authentication with public key authentication. The argument must be ``yes'' or ``no''. The default is ``no''. This option applies to protocol version 2 only and is similar to RhostsRSAAuthentication. HostbasedKeyTypes Specifies the key types that will be used for hostbased authenti- cation as a comma-separated pattern list. The default ``*'' will allow all key types. The -Q option of ssh(1) may be used to list supported key types. HostKeyAlgorithms Specifies the protocol version 2 host key algorithms that the client wants to use in order of preference. The default for this option is: ecdsa-sha2-nistp256-cert-v01@openssh.com, ecdsa-sha2-nistp384-cert-v01@openssh.com, ecdsa-sha2-nistp521-cert-v01@openssh.com, ssh-ed25519-cert-v01@openssh.com, ssh-rsa-cert-v01@openssh.com,ssh-dss-cert-v01@openssh.com, ssh-rsa-cert-v00@openssh.com,ssh-dss-cert-v00@openssh.com, ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521, ssh-ed25519,ssh-rsa,ssh-dss If hostkeys are known for the destination host then this default is modified to prefer their algorithms. The list of available key types may also be obtained using the -Q option of ssh(1) with an argument of ``key''. HostKeyAlias Specifies an alias that should be used instead of the real host name when looking up or saving the host key in the host key data- base files. This option is useful for tunneling SSH connections or for multiple servers running on a single host. HostName Specifies the real host name to log into. This can be used to specify nicknames or abbreviations for hosts. If the hostname contains the character sequence `%h', then this will be replaced with the host name specified on the command line (this is useful for manipulating unqualified names). The character sequence `%%' will be replaced by a single `%' character, which may be used when specifying IPv6 link-local addresses. The default is the name given on the command line. Numeric IP addresses are also permitted (both on the command line and in HostName specifications). IdentitiesOnly Specifies that ssh(1) should only use the authentication identity files configured in the ssh_config files, even if ssh-agent(1) or a PKCS11Provider offers more identities. The argument to this keyword must be ``yes'' or ``no''. This option is intended for situations where ssh-agent offers many different identities. The default is ``no''. IdentityFile Specifies a file from which the user's DSA, ECDSA, Ed25519 or RSA authentication identity is read. The default is ~/.ssh/identity for protocol version 1, and ~/.ssh/id_dsa, ~/.ssh/id_ecdsa, ~/.ssh/id_ed25519 and ~/.ssh/id_rsa for protocol version 2. Additionally, any identities represented by the authentication agent will be used for authentication unless IdentitiesOnly is set. ssh(1) will try to load certificate information from the filename obtained by appending -cert.pub to the path of a speci- fied IdentityFile. The file name may use the tilde syntax to refer to a user's home directory or one of the following escape characters: `%d' (local user's home directory), `%u' (local user name), `%l' (local host name), `%h' (remote host name) or `%r' (remote user name). It is possible to have multiple identity files specified in con- figuration files; all these identities will be tried in sequence. Multiple IdentityFile directives will add to the list of identi- ties tried (this behaviour differs from that of other configura- tion directives). IdentityFile may be used in conjunction with IdentitiesOnly to select which identities in an agent are offered during authenti- cation. IgnoreUnknown Specifies a pattern-list of unknown options to be ignored if they are encountered in configuration parsing. This may be used to suppress errors if ssh_config contains options that are unrecog- nised by ssh(1). It is recommended that IgnoreUnknown be listed early in the configuration file as it will not be applied to unknown options that appear before it. IPQoS Specifies the IPv4 type-of-service or DSCP class for connections. Accepted values are ``af11'', ``af12'', ``af13'', ``af21'', ``af22'', ``af23'', ``af31'', ``af32'', ``af33'', ``af41'', ``af42'', ``af43'', ``cs0'', ``cs1'', ``cs2'', ``cs3'', ``cs4'', ``cs5'', ``cs6'', ``cs7'', ``ef'', ``lowdelay'', ``throughput'', ``reliability'', or a numeric value. This option may take one or two arguments, separated by whitespace. If one argument is spec- ified, it is used as the packet class unconditionally. If two values are specified, the first is automatically selected for interactive sessions and the second for non-interactive sessions. The default is ``lowdelay'' for interactive sessions and ``throughput'' for non-interactive sessions. KbdInteractiveAuthentication Specifies whether to use keyboard-interactive authentication. The argument to this keyword must be ``yes'' or ``no''. The default is ``yes''. KbdInteractiveDevices Specifies the list of methods to use in keyboard-interactive authentication. Multiple method names must be comma-separated. The default is to use the server specified list. The methods available vary depending on what the server supports. For an OpenSSH server, it may be zero or more of: ``bsdauth'', ``pam'', and ``skey''. KexAlgorithms Specifies the available KEX (Key Exchange) algorithms. Multiple algorithms must be comma-separated. The default is: curve25519-sha256@libssh.org, ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521, diffie-hellman-group-exchange-sha256, diffie-hellman-group14-sha1, diffie-hellman-group-exchange-sha1, diffie-hellman-group1-sha1 The list of available key exchange algorithms may also be obtained using the -Q option of ssh(1) with an argument of ``kex''. LocalCommand Specifies a command to execute on the local machine after suc- cessfully connecting to the server. The command string extends to the end of the line, and is executed with the user's shell. The following escape character substitutions will be performed: `%d' (local user's home directory), `%h' (remote host name), `%l' (local host name), `%n' (host name as provided on the command line), `%p' (remote port), `%r' (remote user name) or `%u' (local user name) or `%C' by a hash of the concatenation: %l%h%p%r. The command is run synchronously and does not have access to the session of the ssh(1) that spawned it. It should not be used for interactive commands. This directive is ignored unless PermitLocalCommand has been enabled. LocalForward Specifies that a TCP port on the local machine be forwarded over the secure channel to the specified host and port from the remote machine. The first argument must be [bind_address:]port and the second argument must be host:hostport. IPv6 addresses can be specified by enclosing addresses in square brackets. Multiple forwardings may be specified, and additional forwardings can be given on the command line. Only the superuser can forward privi- leged ports. By default, the local port is bound in accordance with the GatewayPorts setting. However, an explicit bind_address may be used to bind the connection to a specific address. The bind_address of ``localhost'' indicates that the listening port be bound for local use only, while an empty address or `*' indi- cates that the port should be available from all interfaces. LogLevel Gives the verbosity level that is used when logging messages from ssh(1). The possible values are: QUIET, FATAL, ERROR, INFO, VER- BOSE, DEBUG, DEBUG1, DEBUG2, and DEBUG3. The default is INFO. DEBUG and DEBUG1 are equivalent. DEBUG2 and DEBUG3 each specify higher levels of verbose output. MACs Specifies the MAC (message authentication code) algorithms in order of preference. The MAC algorithm is used in protocol ver- sion 2 for data integrity protection. Multiple algorithms must be comma-separated. The algorithms that contain ``-etm'' calcu- late the MAC after encryption (encrypt-then-mac). These are con- sidered safer and their use recommended. The default is: umac-64-etm@openssh.com,umac-128-etm@openssh.com, hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com, umac-64@openssh.com,umac-128@openssh.com, hmac-sha2-256,hmac-sha2-512, hmac-md5-etm@openssh.com,hmac-sha1-etm@openssh.com, hmac-ripemd160-etm@openssh.com, hmac-sha1-96-etm@openssh.com,hmac-md5-96-etm@openssh.com, hmac-md5,hmac-sha1,hmac-ripemd160, hmac-sha1-96,hmac-md5-96 The list of available MAC algorithms may also be obtained using the -Q option of ssh(1) with an argument of ``mac''. NoHostAuthenticationForLocalhost This option can be used if the home directory is shared across machines. In this case localhost will refer to a different machine on each of the machines and the user will get many warn- ings about changed host keys. However, this option disables host authentication for localhost. The argument to this keyword must be ``yes'' or ``no''. The default is to check the host key for localhost. NumberOfPasswordPrompts Specifies the number of password prompts before giving up. The argument to this keyword must be an integer. The default is 3. PasswordAuthentication Specifies whether to use password authentication. The argument to this keyword must be ``yes'' or ``no''. The default is ``yes''. PermitLocalCommand Allow local command execution via the LocalCommand option or using the !command escape sequence in ssh(1). The argument must be ``yes'' or ``no''. The default is ``no''. PKCS11Provider Specifies which PKCS#11 provider to use. The argument to this keyword is the PKCS#11 shared library ssh(1) should use to commu- nicate with a PKCS#11 token providing the user's private RSA key. Port Specifies the port number to connect on the remote host. The default is 22. PreferredAuthentications Specifies the order in which the client should try protocol 2 authentication methods. This allows a client to prefer one method (e.g. keyboard-interactive) over another method (e.g. password). The default is: gssapi-with-mic,hostbased,publickey, keyboard-interactive,password Protocol Specifies the protocol versions ssh(1) should support in order of preference. The possible values are `1' and `2'. Multiple ver- sions must be comma-separated. When this option is set to ``2,1'' ssh will try version 2 and fall back to version 1 if ver- sion 2 is not available. The default is `2'. ProxyCommand Specifies the command to use to connect to the server. The com- mand string extends to the end of the line, and is executed using the user's shell `exec' directive to avoid a lingering shell process. In the command string, any occurrence of `%h' will be substituted by the host name to connect, `%p' by the port, and `%r' by the remote user name. The command can be basically anything, and should read from its standard input and write to its standard output. It should eventually connect an sshd(8) server running on some machine, or execute sshd -i somewhere. Host key manage- ment will be done using the HostName of the host being connected (defaulting to the name typed by the user). Setting the command to ``none'' disables this option entirely. Note that CheckHostIP is not available for connects with a proxy command. This directive is useful in conjunction with nc(1) and its proxy support. For example, the following directive would connect via an HTTP proxy at 192.0.2.0: ProxyCommand /usr/bin/nc -X connect -x 192.0.2.0:8080 %h %p ProxyUseFdpass Specifies that ProxyCommand will pass a connected file descriptor back to ssh(1) instead of continuing to execute and pass data. The default is ``no''. PubkeyAuthentication Specifies whether to try public key authentication. The argument to this keyword must be ``yes'' or ``no''. The default is ``yes''. This option applies to protocol version 2 only. RekeyLimit Specifies the maximum amount of data that may be transmitted before the session key is renegotiated, optionally followed a maximum amount of time that may pass before the session key is renegotiated. The first argument is specified in bytes and may have a suffix of `K', `M', or `G' to indicate Kilobytes, Megabytes, or Gigabytes, respectively. The default is between `1G' and `4G', depending on the cipher. The optional second value is specified in seconds and may use any of the units docu- mented in the TIME FORMATS section of sshd_config(5). The default value for RekeyLimit is ``default none'', which means that rekeying is performed after the cipher's default amount of data has been sent or received and no time based rekeying is done. This option applies to protocol version 2 only. RemoteForward Specifies that a TCP port on the remote machine be forwarded over the secure channel to the specified host and port from the local machine. The first argument must be [bind_address:]port and the second argument must be host:hostport. IPv6 addresses can be specified by enclosing addresses in square brackets. Multiple forwardings may be specified, and additional forwardings can be given on the command line. Privileged ports can be forwarded only when logging in as root on the remote machine. If the port argument is `0', the listen port will be dynamically allocated on the server and reported to the client at run time. If the bind_address is not specified, the default is to only bind to loopback addresses. If the bind_address is `*' or an empty string, then the forwarding is requested to listen on all inter- faces. Specifying a remote bind_address will only succeed if the server's GatewayPorts option is enabled (see sshd_config(5)). RequestTTY Specifies whether to request a pseudo-tty for the session. The argument may be one of: ``no'' (never request a TTY), ``yes'' (always request a TTY when standard input is a TTY), ``force'' (always request a TTY) or ``auto'' (request a TTY when opening a login session). This option mirrors the -t and -T flags for ssh(1). RevokedHostKeys Specifies revoked host public keys. Keys listed in this file will be refused for host authentication. Note that if this file does not exist or is not readable, then host authentication will be refused for all hosts. Keys may be specified as a text file, listing one public key per line, or as an OpenSSH Key Revocation List (KRL) as generated by ssh-keygen(1). For more information on KRLs, see the KEY REVOCATION LISTS section in ssh-keygen(1). RhostsRSAAuthentication Specifies whether to try rhosts based authentication with RSA host authentication. The argument must be ``yes'' or ``no''. The default is ``no''. This option applies to protocol version 1 only and requires ssh(1) to be setuid root. RSAAuthentication Specifies whether to try RSA authentication. The argument to this keyword must be ``yes'' or ``no''. RSA authentication will only be attempted if the identity file exists, or an authentica- tion agent is running. The default is ``yes''. Note that this option applies to protocol version 1 only. SendEnv Specifies what variables from the local environ(7) should be sent to the server. Note that environment passing is only supported for protocol 2. The server must also support it, and the server must be configured to accept these environment variables. Refer to AcceptEnv in sshd_config(5) for how to configure the server. Variables are specified by name, which may contain wildcard char- acters. Multiple environment variables may be separated by whitespace or spread across multiple SendEnv directives. The default is not to send any environment variables. See PATTERNS for more information on patterns. ServerAliveCountMax Sets the number of server alive messages (see below) which may be sent without ssh(1) receiving any messages back from the server. If this threshold is reached while server alive messages are being sent, ssh will disconnect from the server, terminating the session. It is important to note that the use of server alive messages is very different from TCPKeepAlive (below). The server alive messages are sent through the encrypted channel and there- fore will not be spoofable. The TCP keepalive option enabled by TCPKeepAlive is spoofable. The server alive mechanism is valu- able when the client or server depend on knowing when a connec- tion has become inactive. The default value is 3. If, for example, ServerAliveInterval (see below) is set to 15 and ServerAliveCountMax is left at the default, if the server becomes unresponsive, ssh will disconnect after approximately 45 seconds. This option applies to protocol version 2 only. ServerAliveInterval Sets a timeout interval in seconds after which if no data has been received from the server, ssh(1) will send a message through the encrypted channel to request a response from the server. The default is 0, indicating that these messages will not be sent to the server. This option applies to protocol version 2 only. StreamLocalBindMask Sets the octal file creation mode mask (umask) used when creating a Unix-domain socket file for local or remote port forwarding. This option is only used for port forwarding to a Unix-domain socket file. The default value is 0177, which creates a Unix-domain socket file that is readable and writable only by the owner. Note that not all operating systems honor the file mode on Unix-domain socket files. StreamLocalBindUnlink Specifies whether to remove an existing Unix-domain socket file for local or remote port forwarding before creating a new one. If the socket file already exists and StreamLocalBindUnlink is not enabled, ssh will be unable to forward the port to the Unix- domain socket file. This option is only used for port forwarding to a Unix-domain socket file. The argument must be ``yes'' or ``no''. The default is ``no''. StrictHostKeyChecking If this flag is set to ``yes'', ssh(1) will never automatically add host keys to the ~/.ssh/known_hosts file, and refuses to con- nect to hosts whose host key has changed. This provides maximum protection against trojan horse attacks, though it can be annoy- ing when the /etc/ssh/ssh_known_hosts file is poorly maintained or when connections to new hosts are frequently made. This option forces the user to manually add all new hosts. If this flag is set to ``no'', ssh will automatically add new host keys to the user known hosts files. If this flag is set to ``ask'', new host keys will be added to the user known host files only after the user has confirmed that is what they really want to do, and ssh will refuse to connect to hosts whose host key has changed. The host keys of known hosts will be verified automati- cally in all cases. The argument must be ``yes'', ``no'', or ``ask''. The default is ``ask''. TCPKeepAlive Specifies whether the system should send TCP keepalive messages to the other side. If they are sent, death of the connection or crash of one of the machines will be properly noticed. However, this means that connections will die if the route is down tempo- rarily, and some people find it annoying. The default is ``yes'' (to send TCP keepalive messages), and the client will notice if the network goes down or the remote host dies. This is important in scripts, and many users want it too. To disable TCP keepalive messages, the value should be set to ``no''. Tunnel Request tun(4) device forwarding between the client and the server. The argument must be ``yes'', ``point-to-point'' (layer 3), ``ethernet'' (layer 2), or ``no''. Specifying ``yes'' requests the default tunnel mode, which is ``point-to-point''. The default is ``no''. TunnelDevice Specifies the tun(4) devices to open on the client (local_tun) and the server (remote_tun). The argument must be local_tun[:remote_tun]. The devices may be specified by numerical ID or the keyword ``any'', which uses the next available tunnel device. If remote_tun is not specified, it defaults to ``any''. The default is ``any:any''. UpdateHostKeys Specifies whether ssh(1) should accept notifications of addi- tional hostkeys from the server sent after authentication has completed and add them to UserKnownHostsFile. The argument must be ``yes'', ``no'' (the default) or ``ask''. Enabling this option allows learning alternate hostkeys for a server and sup- ports graceful key rotation by allowing a server to send replace- ment public keys before old ones are removed. Additional hostkeys are only accepted if the key used to authenticate the host was already trusted or explicity accepted by the user. If UpdateHostKeys is set to ``ask'', then the user is asked to con- firm the modifications to the known_hosts file. Confirmation is currently incompatible with ControlPersist, and will be disabled if it is enabled. Presently, only sshd(8) from OpenSSH 6.8 and greater support the ``hostkeys@openssh.com'' protocol extension used to inform the client of all the server's hostkeys. UsePrivilegedPort Specifies whether to use a privileged port for outgoing connec- tions. The argument must be ``yes'' or ``no''. The default is ``no''. If set to ``yes'', ssh(1) must be setuid root. Note that this option must be set to ``yes'' for RhostsRSAAuthentication with older servers. User Specifies the user to log in as. This can be useful when a dif- ferent user name is used on different machines. This saves the trouble of having to remember to give the user name on the com- mand line. UserKnownHostsFile Specifies one or more files to use for the user host key data- base, separated by whitespace. The default is ~/.ssh/known_hosts, ~/.ssh/known_hosts2. VerifyHostKeyDNS Specifies whether to verify the remote key using DNS and SSHFP resource records. If this option is set to ``yes'', the client will implicitly trust keys that match a secure fingerprint from DNS. Insecure fingerprints will be handled as if this option was set to ``ask''. If this option is set to ``ask'', information on fingerprint match will be displayed, but the user will still need to confirm new host keys according to the StrictHostKeyChecking option. The argument must be ``yes'', ``no'', or ``ask''. The default is ``no''. Note that this option applies to protocol version 2 only. See also VERIFYING HOST KEYS in ssh(1). VisualHostKey If this flag is set to ``yes'', an ASCII art representation of the remote host key fingerprint is printed in addition to the fingerprint string at login and for unknown host keys. If this flag is set to ``no'', no fingerprint strings are printed at login and only the fingerprint string will be printed for unknown host keys. The default is ``no''. XAuthLocation Specifies the full pathname of the xauth(1) program. The default is /usr/X11R6/bin/xauth.
PATTERNS
A pattern consists of zero or more non-whitespace characters, `*' (a wildcard that matches zero or more characters), or `?' (a wildcard that matches exactly one character). For example, to specify a set of decla- rations for any host in the ``.co.uk'' set of domains, the following pat- tern could be used: Host *.co.uk The following pattern would match any host in the 192.168.0.[0-9] network range: Host 192.168.0.? A pattern-list is a comma-separated list of patterns. Patterns within pattern-lists may be negated by preceding them with an exclamation mark (`!'). For example, to allow a key to be used from anywhere within an organization except from the ``dialup'' pool, the following entry (in authorized_keys) could be used: from="!*.dialup.example.com,*.example.com"
FILES
~/.ssh/config This is the per-user configuration file. The format of this file is described above. This file is used by the SSH client. Because of the potential for abuse, this file must have strict permissions: read/write for the user, and not accessible by oth- ers. /etc/ssh/ssh_config Systemwide configuration file. This file provides defaults for those values that are not specified in the user's configuration file, and for those users who do not have a configuration file. This file must be world-readable.
SEE ALSO
ssh(1)
AUTHORS
OpenSSH is a derivative of the original and free ssh 1.2.12 release by Tatu Ylonen. Aaron Campbell, Bob Beck, Markus Friedl, Niels Provos, Theo de Raadt and Dug Song removed many bugs, re-added newer features and cre- ated OpenSSH. Markus Friedl contributed the support for SSH protocol versions 1.5 and 2.0. NetBSD 7.0 February 20 2015 NetBSD 7.0
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.