- NetBSD Manual Pages
AMR(4) NetBSD Kernel Interfaces Manual AMR(4)
Powered by man-cgi (2021-03-02).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.
amr -- AMI MegaRAID PCI-SCSI RAID driver
amr* at pci? dev ? function ?
scsibus* at amr?
The amr driver provides support for LSI (formerly American Megatrends)
MegaRAID Express, Elite and Enterprise family RAID controllers for SCSI
and SATA, including models relabeled and sold by Dell, Hewlett-Packard,
and Intel. Supported controllers include:
· MegaRAID 320-1
· MegaRAID 320-2
· MegaRAID Series 418
· MegaRAID Enterprise 1200 (Series 428)
· MegaRAID Enterprise 1300 (Series 434)
· MegaRAID Enterprise 1400 (Series 438)
· MegaRAID Enterprise 1500 (Series 467)
· MegaRAID Enterprise 1600 (Series 471)
· MegaRAID Elite 1500 (Series 467)
· MegaRAID Elite 1600 (Series 493)
· MegaRAID Express 100 (Series 466WS)
· MegaRAID Express 200 (Series 466)
· MegaRAID Express 300 (Series 490)
· LSI MegaRAID SCSI 320-0X, 320-2X, 320-4X
· LSI MegaRAID SCSI 320-1E, 320-2E
· LSI MegaRAID SATA 300-6x, 300-8x
· Dell PERC
· Dell PERC 2/SC
· Dell PERC 2/DC
· Dell PERC 4/Di
· Dell PERC 4/SC
· Dell PERC 4e/Si
· HP NetRAID-1/Si
· HP NetRAID-3/Si
· HP Embedded NetRAID
· Intel SRCU42X
· Intel SRCU42E
· Intel SRMOBU42E
· Intel SRCS28X
Driver initialisation/shutdown phase
amr%d: memory window not available
amr%d: I/O window not available
The PCI BIOS did not allocate resources necessary for the correct opera-
tion of the controller. The driver cannot attach to this controller.
amr%d: busmaster bit not set, enabling
The PCI BIOS did not enable busmaster DMA, which is required for the cor-
rect operation of the controller. The driver has enabled this bit and
initialisation will proceed.
amr%d: can't allocate register window
amr%d: can't allocate interrupt
amr%d: can't set up interrupt
amr%d: can't allocate parent DMA tag
amr%d: can't allocate buffer DMA tag
amr%d: can't allocate scatter/gather DMA tag
amr%d: can't allocate s/g table
amr%d: can't allocate mailbox tag
amr%d: can't allocate mailbox memory
A resource allocation error occurred while initialising the driver; ini-
tialisation has failed and the driver will not attach to this controller.
amr%d: can't obtain configuration data from controller
amr%d: can't obtain product data from controller
The driver was unable to obtain vital configuration data from the con-
troller. Initialisation has failed and the driver will not attach to
amr%d: can't establish configuration hook
amr%d: can't scan controller for drives
The scan for logical drives managed by the controller failed. No drives
will be attached.
amr%d: device_add_child failed
amr%d: bus_generic_attach returned %d
Creation of the logical drive instances failed; attachment of one or more
logical drives may have been aborted.
amr%d: flushing cache...
The controller cache is being flushed prior to shutdown or detach.
amr%d: I/O beyond end of unit (%u,%d > %u)
A partitioning error or disk corruption has caused an I/O request beyond
the end of the logical drive. This may also occur if FlexRAID Virtual
Sizing is enabled and an I/O operation is attempted on a portion of the
virtual drive beyond the actual capacity available.
amr%d: polled command timeout
An initialisation command timed out. The initialisation process may fail
as a result.
amr%d: bad slot %d completed
The controller reported completion of a command that the driver did not
issue. This may result in data corruption, and suggests a hardware or
firmware problem with the system or controller.
amr%d: I/O error - %x
An I/O error has occurred.
cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), st(4), amrctl(8)
NetBSD 5.0.1 July 23, 2006 NetBSD 5.0.1