disklabel(8)
- NetBSD Manual Pages
DISKLABEL(8) NetBSD System Manager's Manual DISKLABEL(8)
NAME
disklabel - read and write disk pack label
SYNOPSIS
disklabel [-CFrt] disk
disklabel -w [-] [-f disktab] disk disktype [packid]
disklabel -e [-CFIr] disk
disklabel -i [-FIr] disk
disklabel -R [-] disk protofile
disklabel [-NW] disk
disklabel -B [-F] [-f disktab] [-b boot1 [-s boot2]] disk [disktype]
disklabel -w -B [-F] [-f disktab] [-b boot1 [-s boot2]] disk disktype
[packid]
disklabel -R -B [-F] [-f disktab] [-b boot1 [-s boot2]] disk protofile
[disktype]
DESCRIPTION
disklabel can be used to install, examine or modify the label on a disk
drive or pack. When writing the label, it can be used to change the
drive identification, the disk partitions on the drive, or to replace a
damaged label. On some systems, disklabel can be used to install boot-
strap code as well.
There are several forms of the command that read (display), install, or
edit the label on a disk. Each form has an additional option, -r, which
causes the label to be read from or written to the disk directly, rather
than going through the system's in-core copy of the label. This option
may allow a label to be installed on a disk without kernel support for a
label, such as when labels are first installed on a system; it must be
used when first installing a label on a disk. Any special effects of the
-r flag are described with the affected commands.
The -F option indicates that disklabel should treat disk as if it is a
regular file, instead of as if it is a block device, for the purposes of
reading and writing a disklabel.
The -I option is similar to the -r option but provides defaults instead
of failing with an error, if there is no existing disklabel on the disk.
The read and install forms also support the -B option to install boot-
strap code on some platforms, e.g., hp300, vax, and arm32. The -B option
is not supported on all platforms. These variants are described later.
The first form of the command (read) is used to examine the label on the
named disk drive (e.g., sd0 or /dev/rsd0c). It will display all of the
parameters associated with the drive and its partition layout. Unless
the -r flag is given, the kernel's in-core copy of the label is dis-
played; if the disk has no label, or the partition types on the disk are
incorrect, the kernel may have constructed or modified the label. If the
-r flag is given, the label from the raw disk will be displayed rather
than the in-core label. If the -t flag is given, then the label will be
formatted as a disktab(5) entry.
The second form of the command, with the -w flag, is used to write a
standard label on the designated drive. The required arguments to
disklabel are the drive to be labelled (e.g., sd0), and the drive type as
described in the disktab(5) file. The drive parameters and partitions
are taken from that file. If different disks of the same physical type
are to have different partitions, it will be necessary to have separate
disktab entries describing each, or to edit the label after installation
as described below. The optional argument is a pack identification
string, up to 16 characters long. The pack id must be quoted if it con-
tains blanks. If the disk does not already have a label, the -r flag
must be used. In either case, the kernel's in-core label is replaced.
An alternate disktab(5) file may be specified with the -f disktab option.
An existing disk label may be edited by using the -e flag. The label is
formatted and then supplied to an editor for changes. If no editor is
specified in an EDITOR environment variable, vi(1) is used. When the
editor terminates, the formatted label is reread and used to rewrite the
disk label.
Labels can also created interactively using the -i flag.
The -C flag causes the partition offset and size values to be displayed
in <cylinder/track/sector> format. Note that, regardless of whether -C
was specified, this format is always accepted by disklabel on input with
either the -e or -R flag.
With the -R flag, disklabel is capable of restoring a disk label that was
formatted in a prior operation and saved in an ascii file. The prototype
file used to create the label should be in the same format as that pro-
duced when reading or editing a label. Comments are delimited by # and
newline.
The -NW flags for disklabel explicitly disallow and allow, respectively,
writing of the pack label area on the selected disk.
The final three forms of disklabel are used to install bootstrap code on
machines where the bootstrap is part of the label. The bootstrap code is
composed of one or two boot programs depending on the machine. The -B
option is used (on some platforms only, see above) to denote that boot-
strap code is to be installed. The -r flag is implied by -B and never
needs to be specified. The name of the boot program(s) to be installed
can be selected in a variety of ways. First, the names can be specified
explicitly via the -b and -s flags. On machines with only a single level
of boot program, -b is the name of that program. For machines with a
two-level bootstrap, -b indicates the primary boot program and -s the
secondary boot program. If the names are not explicitly given, standard
boot programs will be used. The boot programs are located in /usr/mdec.
The names of the programs are taken from the ``b0'' and ``b1'' parameters
of the disktab(5) entry for the disk if disktype was given and its disk-
tab entry exists and includes those parameters. Otherwise, boot program
names are derived from the name of the disk. These names are of the form
basenameboot for the primary (or only) bootstrap, and bootbasename for
the secondary bootstrap; for example, /usr/mdec/sdboot and
/usr/mdec/bootsd if the disk device is sd0.
The first of the three boot-installation forms is used to install boot-
strap code without changing the existing label. It is essentially a read
command with respect to the disk label itself and all options are related
to the specification of the boot program as described previously. The
final two forms are analogous to the basic write and restore versions
except that they will install bootstrap code in addition to a new label.
FILES
/etc/disktab
/usr/mdec/xxboot
/usr/mdec/bootxx
EXAMPLES
disklabel sd0
Display the in-core label for sd0 as obtained via /dev/rsd0c.
disklabel -w -r /dev/rsd0c sd2212 foo
Create a label for sd0 based on information for ``sd2212'' found in
/etc/disktab, using foo as the disk pack label. Any existing bootstrap
code will be clobbered. If you do not have an entry for your disk in
/etc/disktab, you can use this style to put an initial label onto a new
disk. Then dump the label to a file (using disklabel sd0 > protofile),
editing the file, and replacing the label with disklabel -R sd0
protofile.
disklabel -e -r sd0
Read the on-disk label for sd0, edit it and reinstall in-core as well as
on-disk. Existing bootstrap code is unaffected.
disklabel -e -I sd0
As previous, but don't fail if there was no label on the disk yet; pro-
vide some default values instead.
disklabel -i -I sd0
As previous, only use the built-in interactive editor.
disklabel -R sd0 mylabel
Restore the on-disk and in-core label for sd0 from information in
mylabel. Existing bootstrap code is unaffected.
disklabel -B sd0
Install a new bootstrap on sd0 (only for platforms which support the -B
option, see above). The boot code comes from /usr/mdec/sdboot and possi-
bly /usr/mdec/bootsd. On-disk and in-core labels are unchanged.
disklabel -w -B /dev/rsd0c -b newboot sd2212
Install a new label and bootstrap (on platforms which support the -B
option, see above). The label is derived from disktab information for
``sd2212'' and installed both in-core and on-disk. The bootstrap code
comes from the file /usr/mdec/newboot.
disklabel -R -r sd0 <protofile>
Install a new label and bootstrap on a disk, from a prototype label file.
This is a good way to install a label on a previously unlabeled disk for
which no entry appears in /etc/disktab, if you create the prototype file
by dumping some other disk's label to a file and editing it appropriately
(total size, partition offsets, types, etc.)
DIAGNOSTICS
The kernel device drivers will not allow the size of a disk partition to
be decreased or the offset of a partition to be changed while it is open.
Some device drivers create a label containing only a single large parti-
tion if a disk is unlabeled; thus, the label must be written to the ``a''
partition of the disk while it is open. This sometimes requires the
desired label to be set in two steps, the first one creating at least one
other partition, and the second setting the label on the new partition
while shrinking the ``a'' partition.
On some machines the bootstrap code may not fit entirely in the area
allocated for it by some filesystems. As a result, it may not be possi-
ble to have filesystems on some partitions of a ``bootable'' disk. When
installing bootstrap code, disklabel checks for these cases. If the
installed boot code would overlap a partition of type FS_UNUSED it is
marked as type FS_BOOT. The newfs(8) utility will disallow creation of
filesystems on FS_BOOT partitions. Conversely, if a partition has a type
other than FS_UNUSED or FS_BOOT, disklabel will not install bootstrap
code that overlaps it.
SEE ALSO
disklabel(5), disktab(5), dkctl(8), fdisk(8), installboot(8),
mbrlabel(8), mscdlabel(8)
BUGS
If the disk partition is not specified in the disk name (i.e., ``xy0''
instead of ``/dev/rxy0c''), disklabel will construct the full pathname of
the disk and use the ``d'' partition on i386, hpcmips, or arc, and the
``c'' partition on all others.
On the sparc, sparc64, sun2, and sun3 NetBSD systems, the size of each
partition must be a multiple of the number of sectors per cylinder (i.e.,
each partition must be an integer number of cylinders), or the boot ROMs
will declare the label invalid and fail to boot the system.
In addition, the -r option should never be used on a sparc, sparc64, sun2
or sun3 system boot disk - the NetBSD kernel translates the NetBSD disk
label into a SunOS compatible format (which is required by the boot
PROMs) when it writes the label. Using the -r flag causes disklabel to
write directly to disk, and bypass the format translation. This will
result in a disk label that the PROMs will not recognize, and that there-
fore cannot be booted from.
NetBSD 2.0.2 March 18, 2004 NetBSD 2.0.2
Powered by man-cgi (2024-03-20).
Maintained for NetBSD
by Kimmo Suominen.
Based on man-cgi by Panagiotis Christias.