UTOPPY(4) NetBSD Kernel Interfaces Manual UTOPPY(4)
NAME
utoppy -- USB driver for the Topfield TF5000PVR range of digital video recorders
SYNOPSIS
utoppy* at uhub? port ? #include <dev/usb/utoppy.h>
DESCRIPTION
The utoppy driver provides support for the Topfield TF5000PVR range of DVB recorders (nicknamed `Toppy') which are popular in Europe and Aus- tralia. These recorders have a USB device interface which can be used to transfer recordings to and from the unit's hard disk. The USB interface can also be used to upload binary images for execution on the Toppy's MIPS cpu. The Toppy's USB protocol has not been officially documented by Topfield, but the basic features have been reverse engineered by others in order to write replacements for the official `Altair' download/upload program from Topfield. Existing replacements for Altair suffer from the fact that they are ulti- mately built on top of ugen(4). This has a number of detrimental side- effects: 1. Performance suffers since all Toppy command packets have to cross the user-kernel interface. 2. The userland programs are full of clutter to deal with interpreting the command/status packets, not to mention byte-swapping and host endian issues. 3. Signals can interrupt a data transfer at a critical point, leaving the Toppy in an undefined state. For example, interrupting a down- load with `Turbo' mode enabled will leave the Toppy completely unre- sponsive to the remote control, and prevent timer-based recordings from starting. The utoppy driver provides a clean and stable interface to the Toppy pro- tocol, and ensures that an interrupt caused by a signal does not leave the Toppy in an undefined state.
UTOPPY INTERFACE
Use the following header file to get access to the utoppy specific struc- tures and defines. #include <dev/usb/utoppy.h> The utoppy driver can be accessed through the /dev/utoppyN character device. The primary means of controlling the driver is by issuing a series of ioctl(2) system calls followed by read(2) or write(2) system calls as appropriate. The following ioctl(2) commands are supported by the utoppy driver: UTOPPYIOTURBO int *mode This command can be used to enable or disable `Turbo' mode for subsequent UTOPPYIOREADFILE or UTOPPYIOWRITEFILE commands (see below). If num is non-zero, Turbo mode will be enabled. Other- wise Turbo mode will be disabled. In non-Turbo mode, the Toppy's USB interface is capable of sustaining around 5.6 Mbit/s during a file transfer. With Turbo mode enabled, it can sustain just over 16 Mbit/s. Of course, these figures are valid only if the Toppy is connected via a USB 2.0 interface. Performance using an older USB 1 interface will be significantly lower. UTOPPYIOCANCEL void This command can be used to abort an in-progress UTOPPYIOREADDIR, UTOPPYIOREADFILE, or UTOPPYIOWRITEFILE command. UTOPPYIOREBOOT void This command will cause the Toppy to reboot cleanly. UTOPPYIOSTATS struct utoppy_stats *stats This command retrieves statistics for the Toppy's hard disk. struct utoppy_stats { uint64_t us_hdd_size; /* Size of the disk, in bytes */ uint64_t us_hdd_free; /* Free space, in bytes */ }; UTOPPYIORENAME struct utoppy_rename *rename This command is used to rename a file or directory on the Toppy's hard disk. The full pathname to each file must be provided. struct utoppy_rename { char *ur_old_path; /* Path to existing file */ char *ur_new_path; /* Path to new file */ }; UTOPPYIOMKDIR char *path This command creates the directory specified by path. UTOPPYIODELETE char *path This command deletes the file or directory specified by path. UTOPPYIOREADDIR char *path This command initiates a read of the contents of the directory specified by path. After issuing this command, the directory contents must be read using consecutive read(2) system calls. Each read(2) will transfer one or more directory entries into the user-supplied buffer. The buffer must be large enough to receive at least one directory entry. When read(2) returns zero, all directory entries have been read. A directory entry is described using the following data struc- ture: struct utoppy_dirent { char ud_path[UTOPPY_MAX_FILENAME_LEN + 1]; enum { UTOPPY_DIRENT_UNKNOWN, UTOPPY_DIRENT_DIRECTORY, UTOPPY_DIRENT_FILE } ud_type; off_t ud_size; time_t ud_mtime; uint32_t ud_attributes; }; The ud_path field contains the name of the directory entry. The ud_type field specifies whether the entry corresponds to a file or a sub-directory. The ud_size field is valid for files only, and specifies the file's size in bytes. The ud_mtime field describes the file or directory's modification time, specified as seconds from the Unix epoch. The timestamp is relative to the current timezone, so localtime(3) can be used to convert it into human readable form. Note that the Toppy sets directory timestamps to a predefined value so they are not par- ticularly useful. The ud_attributes field is not used at this time. UTOPPYIOREADFILE struct utoppy_readfile * This command is used to initiate reading a file from the Toppy's hard disk. The full pathname, together with the file offset at which to start reading, is specified using the following data structure: struct utoppy_readfile { char *ur_path; off_t ur_offset; }; After issuing this command, the file must be read using consecu- tive read(2) system calls. When read(2) returns zero, the entire file has been read. UTOPPYIOWRITEFILE struct utoppy_writefile * This command is used to initiate writing to a file on the Toppy's hard disk. The file to be written is described using the follow- ing data structure: struct utoppy_writefile { char *uw_path; off_t uw_offset; off_t uw_size; time_t uw_mtime; }; The uw_path field specifies the full pathname of the file to be written. The uw_offset field specifies the file offset at which to start writing, assuming the file already exists. Otherwise, uw_offset must be zero. The protocol requires that the Toppy must be informed of a file's size in advance of the file being written. This is accomplished using the uw_size field. It may be possible to work around this limitation in a future version of the driver. The uw_mtime field specifies the file's timestamp expressed as seconds from the Unix epoch in the local timezone. Due to limitations with the protocol, a utoppy device can be opened by only one application at a time. Also, only a single UTOPPYIOREADDIR, UTOPPYIOREADFILE, or UTOPPYIOWRITEFILE command can be in progress at any given time.
FILES
/dev/utoppy0 device node
SEE ALSO
utoppya(1), usb(4)
HISTORY
The utoppy driver appeared in NetBSD 4.0.
AUTHORS
Steve C. Woodford <scw@netbsd.org> NetBSD 10.1 April 3, 2006 NetBSD 10.1
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.