autoconf(4) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
AUTOCONF(4)          NetBSD/hp300 Kernel Interfaces Manual         AUTOCONF(4)


NAME

     autoconf -- diagnostics from the autoconfiguration code


DESCRIPTION

     When NetBSD bootstraps it probes the innards of the machine on which it
     is running and locates controllers, drives, and other devices, printing
     out what it finds on the console.  This procedure is driven by a system
     configuration table which is processed by config(1) and compiled into
     each kernel.

     Autoconfiguration on the HP300s is similar to that on the VAX, the pri-
     mary difference is in the naming conventions.  On the HP300, if devices
     exist which are not configured they will be ignored; if devices exist of
     unsupported type they will be ignored.

     Normally, the system uses the disk from which it was loaded as the root
     filesystem.  If that is not possible, a generic system will use `rd0' if
     it exists.  If such a system is booted with the RB_ASKNAME option (see
     reboot(2)), then the name of the root device is read from the console
     terminal at boot time, and any available device may be used.


DIAGNOSTICS

     SPU type not configured  You tried to boot NetBSD on an SPU type which it
     doesn't (or at least this compiled version of NetBSD doesn't) understand.

     nhpib%d at intio0 addr 0x478000 ipl %d
     nhpib%d at dio0 scode %d ipl %d
     fhpib%d at dio0 scode %d ipl %d
     hpibbus%d at nhpib%d
     hpibbus%d at fhpib%d  An HP-IB was found at the internal bus or scode %d
     (the select code) with ipl %d (interrupt priority level).  NetBSD will
     call it hpibbus%d.

     %s%d at hpibbus%d slave %d punit %d
     %s%d: %s  An HP-IB disk or tape controller was found.  For disks `%s%d'
     will look like `rd0', for tapes like `ct0'.  The `%s' in the first line
     will be a product type like ``7945A'' or ``9144''.  The slave number
     comes from the address select switches on the drive.

     dvbox0 at intio0 addr 0x560000
     dvbox%d at dio0 scode %d
     gbox0 at intio0 addr 0x560000
     gbox%d at dio0 scode %d
     hyper%d at dio0 scode %d
     rbox0 at intio0 addr 0x560000
     rbox%d at dio0 scode %d
     topcat0 at intio0 addr 0x560000
     topcat%d at dio0 scode %d
     tvrx%d at dio0 scode %d
     gendiofb%d at dio0 scode %d
     sti%d at sgc0 slot %d  A bit mapped display was found either at the
     ``internal'' address, at some ``external'' select code, or at some SGC
     bus slot.  If it exists, the internal display will always be unit 0.

     %s%d at dio0 scode %d ipl %d  Another peripheral controller was found at
     the indicated select code and with indicated interrupt priority level.
     `%s' will be one of com(4) (single-port serial interfaces), hp300/dcm(4)
     (four-port serial interfaces), or le(4) (LAN cards).  The slave number
     comes from the address select switches on the interface card.


SEE ALSO

     config(1), hp300/intro(4), boot(8)

     4.3BSD for the HP300, in the distribution documentation package.

NetBSD 10.1                      June 17, 2022                     NetBSD 10.1