IFWATCHD(8) NetBSD System Manager's Manual IFWATCHD(8)
NAME
ifwatchd -- watch for addresses added to or deleted from interfaces and call up/down-scripts for them
SYNOPSIS
ifwatchd [-hiqv] [-A arrival-script] [-c carrier-script] [-D departure-script] [-d down-script] [-u up-script] [-n no-carrier-script] ifname(s)
DESCRIPTION
ifwatchd is used to monitor dynamic interfaces (for example PPP inter- faces) for address changes, and to monitor static interfaces for carrier changes. Sometimes these interfaces are accompanied by a daemon program, which can take care of running any necessary scripts (like pppd(8)), but sometimes the interfaces run completely autonomously (like pppoe(4)). ifwatchd provides a generic way to watch these types of changes. It works by monitoring the routing socket and interpreting `RTM_NEWADDR' (address added), `RTM_DELADDR' (address deleted) and `RTM_IFINFO' (carrier detect or loss of carrier) messages. It does not need special privileges to do this. The scripts called for up or down events are run with the same user id as ifwatchd is run. The following options are available: -A arrival-script Specify the command to invoke on arrival of new interfaces (like PCMCIA cards). -c carrier-script Specify the command to invoke when the carrier status transitions from no carrier to carrier. -D departure-script Specify the command to invoke when an interface departs (for example a PCMCIA card is removed.) -d down-script Specify the command to invoke on ``interface down'' events (or: deletion of an address from an interface). -h Show the synopsis. -i Inhibit a call to the up-script on startup for all watched inter- faces already marked up. If this option is not given, ifwatchd will check all watched interfaces on startup whether they are already marked up and, if they are, call the up-script with appropriate parameters. Additionally, if the interface is up and has a link, ifwatchd will run the carrier script. Since ifwatchd typically is started late in the system boot sequence, some of the monitored interfaces may already have come up when it finally starts, but their up-scripts have not been called. By default ifwatchd calls them on startup to account for this (and make the scripts easier.) -n no-carrier-script Specify the command to invoke when the carrier status transitions from carrier to no carrier. -q Be quiet and don't log non-error messages to syslog. -u up-script Specify the command to invoke on ``interface up'' events (or: addition of an address to an interface). -v Run in verbose debug mode and do not detach from the controlling terminal. Output verbose progress messages and flag errors ignored during normal operation. You do not want to use this option in /etc/rc.conf! ifname(s) The name of the interface to watch. Multiple interfaces may be specified. Events for other interfaces are ignored.
EXAMPLES
# ifwatchd -u /etc/ppp/ip-up -d /etc/ppp/ip-down pppoe0 If your pppoe0 interface is your main connection to the internet, the typical use of the up/down scripts is to add and remove a default route. This is an example for an up script doing this: #! /bin/sh /sbin/route add default $5 /sbin/route add -inet6 default fe80::2 -iface ifp $1 As described below the fifth command line parameter will contain the peer address of the pppoe link. The corresponding ip-down script is: #! /bin/sh /sbin/route delete default $5 /sbin/route delete -inet6 default fe80::2 Note that this is not a good idea if you have pppoe0 configured to con- nect only on demand (via the link1 flag), but works well for all perma- nent connected cases. Use ! /sbin/route add default -iface 0.0.0.1 in your /etc/ifconfig.pppoe0 file in the on-demand case.
PARAMETERS PASSED TO SCRIPTS
The invoked scripts get passed these parameters: ifname The name of the interface this change is for (this allows to share the same script for multiple interfaces watched and dispatching on the interface name in the script). tty Dummy parameter for compatibility with pppd(8) which will always be /dev/null. speed Dummy parameter for compatibility with pppd(8) which will always be 9600. address The new address if this is an up event, or the no longer valid old address if this is a down event. The format of the address depends on the address family, for IPv4 it is the usual dotted quad notation, for IPv6 the colon separated standard notation. destination For point to point interfaces, this is the remote address of the interface. For other interfaces it is the broadcast address.
ERRORS
The program logs to the syslog daemon as facility ``daemon''. For detailed debugging use the -v (verbose) option.
SEE ALSO
pppoe(4), route(4), ifconfig.if(5), rc.d(8), route(8)
HISTORY
The ifwatchd utility appeared in NetBSD 1.6.
AUTHORS
The program was written by Martin Husemann <martin@NetBSD.org>.
CAVEATS
Due to the nature of the program a lot of stupid errors can not easily be caught in advance without removing the provided facility for advanced uses. For example typing errors in the interface name can not be detected by checking against the list of installed interfaces, because it is possible for a pcmcia card with the name given to be inserted later. NetBSD 10.1 February 17, 2019 NetBSD 10.1
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.