btconfig(8) - NetBSD Manual Pages

Command:
Section:
Arch:
Collection:
>>>
BTCONFIG(8)             NetBSD System Manager's Manual             BTCONFIG(8)


NAME

     btconfig -- configure bluetooth devices


SYNOPSIS

     btconfig [-svz] [device [parameters]]
     btconfig [-l]


DESCRIPTION

     btconfig is used to configure Bluetooth devices.  If the device is given,
     but no parameters, then btconfig will print information about the device.
     If no device is given, a basic list of devices will be printed.

     When the -l flag is used, just the device names will be printed.


COMMANDS

     The following parameters may be specified with btconfig:

     up           Enable Bluetooth Device.

     down         Disable Bluetooth Device.

     pscan        Enable Page Scan.  This enables incoming connections to the
                  device.

     -pscan       Disable Page Scan.

     iscan        Enable Inquiry Scan.  This puts the device in Discoverable
                  mode.

     -iscan       Disable Inquiry Scan.

     encrypt      Enable encryption.  This will cause the device to request
                  encryption on all baseband connections, and will only work
                  if authentication is also enabled.

     -encrypt     Disable encryption.

     auth         Enable authentication.  This will cause the device to
                  request authentication for all baseband connections.

     -auth        Disable authentication.

     switch       Enable Role Switching.  In a Bluetooth piconet there is one
                  Master and up to seven Slaves, and normally the device that
                  initiates a connection will take the Master role.  Enabling
                  this option allows remote devices to switch connection
                  roles.

     -switch      Disable Role Switching.

     master       Request the Master role when accepting connections.

     -master      Do not request Master role.

     hold         Enable Hold Mode.

     -hold        Disable Hold Mode.

     sniff        Enable Sniff Mode.

     -sniff       Disable Sniff Mode.

     park         Enable Park Mode.

     -park        Disable Park Mode.

     name name    Set human readable name of device.

     ptype type   Set packet types.  type is a 16 bit hex value specifying
                  packet types that will be requested by outgoing ACL connec-
                  tions.  By default, all packet types that the device sup-
                  ports are enabled, see bluetooth specifications for more
                  information if you want to change this.

     class class  Set class of device.  class is a 6 digit hex value the value
                  of which declares the device capabilities.  See the
                  "Assigned Numbers - Baseband" document at
                  http://www.bluetooth.com/ for details of constructing a
                  Class of Device value.  As a starter, 0x020104 means Desktop
                  Computer, with Networking available.

     fixed        Set fixed pin type.

     variable     Set variable pin type.

     inquiry      Perform device Discovery from the specified device and print
                  details.

     imode type   Set inquiry mode type to control which event formats are
                  generated during a device inquiry.  The type can be:

                  std     Standard Inquiry Result Event format.

                  rssi    Enable Remote Signal Strength Indicator (RSSI) in
                          inquiry results.  This will only work if the device
                          features indicate <RSSI with inquiry result>.

                  ext     Inquiry Result with RSSI format or Extended Inquiry
                          Result format.  This will only work where the device
                          features indicate <extended inquiry>, and the
                          Extended Inquiry Result will only occur when the
                          remote device provides the extended information.

     reset        Perform a hard reset on the device and re-initialise system
                  state.

     voice        Set Voice Setting.  [This should be 0x0060 for now]

     pto          Set Page Timeout value.  This is a decimal value in mil-
                  liseconds, indicating how long the device will attempt to
                  page another device when opening baseband connections.

     scomtu       Change SCO mtu value.  This is a decimal value, see ubt(4)
                  for reasons why you may need to do this.

     All parameters are parsed before any device operations take place.  Each
     time the -v flag is given, verbosity levels will be increased.

     Super-user privileges are required to change device configurations.


DIAGNOSTICS

     Messages indicating the specified device does not exist, the requested
     address is unknown, or the user is not privileged and tried to alter a
     device's configuration.


SEE ALSO

     bcsp(4), bluetooth(4), bt3c(4), btbc(4), btuart(4), sbt(4), ubt(4)


HISTORY

     The btconfig command was written for NetBSD 4.0 by Iain Hibbert under the
     sponsorship of Itronix, Inc.


BUGS

     The output is very messy.

NetBSD 10.1                    October 11, 2010                    NetBSD 10.1