read(2) - NetBSD Manual Pages

Command: Section: Arch: Collection:  
READ(2)                   NetBSD Programmer's Manual                   READ(2)

read, readv, pread, preadv - read input
Standard C Library (libc, -lc)
#include <unistd.h> ssize_t read(int d, void *buf, size_t nbytes); ssize_t pread(int d, void *buf, size_t nbytes, off_t offset); #include <sys/uio.h> ssize_t readv(int d, const struct iovec *iov, int iovcnt); ssize_t preadv(int d, const struct iovec *iov, int iovcnt, off_t offset);
read() attempts to read nbytes of data from the object referenced by the descriptor d into the buffer pointed to by buf. readv() performs the same action, but scatters the input data into the iovcnt buffers speci- fied by the members of the iov array: iov[0], iov[1], ..., iov[iovcnt-1]. pread() and preadv() perform the same functions, but read from the speci- fied position in the file without modifying the file pointer. For readv() and preadv(), the iovec structure is defined as: struct iovec { void *iov_base; size_t iov_len; }; Each iovec entry specifies the base address and length of an area in mem- ory where data should be placed. readv() will always fill an area com- pletely before proceeding to the next. On objects capable of seeking, the read() starts at a position given by the pointer associated with d (see lseek(2)). Upon return from read(), the pointer is incremented by the number of bytes actually read. Objects that are not capable of seeking always read from the current po- sition. The value of the pointer associated with such an object is unde- fined. Upon successful completion, read(), readv(), pread(), and preadv() return the number of bytes actually read and placed in the buffer. The system guarantees to read the number of bytes requested if the descriptor refer- ences a normal file that has that many bytes left before the end-of-file, but in no other case.
If successful, the number of bytes actually read is returned. Upon read- ing end-of-file, zero is returned. Otherwise, a -1 is returned and the global variable errno is set to indicate the error.
read(), readv(), pread(), and preadv() will succeed unless: [EBADF] d is not a valid file or socket descriptor open for read- ing. [EFAULT] buf points outside the allocated address space. [EIO] An I/O error occurred while reading from the file system. [EINTR] A read from a slow device was interrupted before any data arrived by the delivery of a signal. [EINVAL] The pointer associated with d was negative. [EINVAL] The total length of the I/O is more than can be expressed by the ssize_t return value. [EAGAIN] The file was marked for non-blocking I/O, and no data were ready to be read. In addition, readv() and preadv() may return one of the following errors: [EINVAL] iovcnt was less than or equal to 0, or greater than {IOV_MAX}. [EINVAL] One of the iov_len values in the iov array was negative. [EINVAL] The sum of the iov_len values in the iov array overflowed a 32-bit integer. [EFAULT] Part of the iov points outside the process's allocated ad- dress space. The pread() and preadv() calls may also return the following errors: [EINVAL] The specified file offset is invalid. [ESPIPE] The file descriptor is associated with a pipe, socket, or FIFO.
dup(2), fcntl(2), open(2), pipe(2), poll(2), select(2), socket(2), socketpair(2)
The read() function conforms to IEEE Std 1003.1-1990 (``POSIX''). The readv() and pread() functions conform to X/Open Portability Guide Issue 4, Version 2 (``XPG4.2'').
The preadv() function call appeared in NetBSD 1.4. The pread() function call appeared in AT&T System V.4 UNIX. The readv() function call ap- peared in 4.2BSD. The read() function call appeared in Version 6 AT&T UNIX. NetBSD 1.6.2 October 16, 2001 2
Powered by man-cgi (2024-03-20). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.