ipsec_set_policy(3) - NetBSD Manual Pages

IPSEC_SET_POLICY(3)       NetBSD Programmer's Manual       IPSEC_SET_POLICY(3)


NAME
ipsec_set_policy, ipsec_get_policylen, ipsec_dump_policy - manipulate IPsec policy specification structure from readable string
LIBRARY
IPsec Policy Control Library (libipsec, -lipsec)
SYNOPSIS
#include <netinet6/ipsec.h> char * ipsec_set_policy(char *policy, int len); int ipsec_get_policylen(char *buf); char * ipsec_dump_policy(char *buf, char *delim);
DESCRIPTION
ipsec_set_policy() generates IPsec policy specification structure, namely struct sadb_x_policy and/or struct sadb_x_ipsecrequest from human-read- able policy specification. policy specification must be given as C string policy and length len of policy. ipsec_set_policy() will return the buffer of IPsec policy specification structure. The buffer is dynam- ically allocated, and must be freed by the caller by calling free(3). You may want the length of the generated buffer such when calling setsockopt(2). ipsec_get_policylen() will return the length. ipsec_dump_policy() converts IPsec policy structure into readable form. Therefore, ipsec_dump_policy() can be regarded as inverse conversion of ipsec_set_policy(). buf points to a IPsec policy structure, struct sadb_x_policy. delim is a delimiter string, which is usually a blank character. If you set delim to NULL, single whitespace is assumed. ipsec_dump_policy() returns pointer to dynamically allocated string. It is caller's responsibility to reclaim the region, by using free(3). policy is formatted as either of the following: direction discard direction must be in or out. direction specifies which direc- tion the policy needs to be applied. With discard policy, pack- ets will be dropped if they match the policy. direction entrust entrust means to consult to SPD defined by setkey(8). direction bypass bypass means to be bypassed the IPsec processing. (packet will be transmitted in clear). This is for privileged socket. direction ipsec request ... ipsec means that the matching packets are subject to IPsec pro- cessing. ipsec can be followed by one or more request string, which is formatted as below: protocol / mode / src - dst [/level] protocol is either ah, esp or ipcomp. mode is either transport or tunnel. src and dst specifies IPsec endpoint. src always means ``sending node'' and dst always means ``receiving node''. Therefore, when direction is in, dst is this node and src is the other node (peer). If mode is transport, Both src and dst can be omitted. level must be set to one of the following: default, use, require or unique. default means that the kernel should consult the system default policy defined by sysctl(8), such as net.inet.ipsec.esp_trans_deflev. See ipsec(4) regarding the system default. use means that a relevant SA can be used when available, since the kernel may perform IPsec operation against packets when possible. In this case, packets can be transmit- ted in clear (when SA is not available), or encrypted (when SA is available). require means that a relevant SA is required, since the kernel must perform IPsec op- eration against packets. unique is the same as require, but adds the restriction that the SA for out- bound traffic is used only for this policy. You may need the identifier in order to relate the policy and the SA when you define the SA by manual keying. You can put the decimal number as the identifier after unique like unique: number. number must be between 1 and 32767 . If the request string is kept unambiguous, level and slash prior to level can be omitted. Howev- er, it is encouraged to specify them explicitly to avoid unintended behaviors. If level is omitted, it will be interpreted as default. Note that there is a bit difference of specification from setkey(8). In specification by setkey(8), both entrust and bypass are not used. Refer to setkey(8) for detail. Here are several examples (long lines are wrapped for readability): in discard out ipsec esp/transport//require in ipsec ah/transport//require out ipsec esp/tunnel/10.1.1.2-10.1.1.1/use in ipsec ipcomp/transport//use esp/transport//use
RETURN VALUES
ipsec_set_policy() returns a pointer to the allocated buffer of policy specification if successful; otherwise a NULL pointer is returned. ipsec_get_policylen() returns with positive value (meaning the buffer size) on success, and negative value on errors. ipsec_dump_policy() re- turns a pointer to dynamically allocated region on success, and NULL on errors.
SEE ALSO
ipsec_strerror(3), ipsec(4), setkey(8)
HISTORY
The functions first appeared in WIDE/KAME IPv6 protocol stack kit. NetBSD 1.6.2 May 5, 1998 2

Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.