IFCONFIG(8) NetBSD System Manager's Manual IFCONFIG(8)
NAME
ifconfig - configure network interface parameters
SYNOPSIS
ifconfig interface address_family [address [dest_address]] [parameters] ifconfig [-m] interface [protocol_family] ifconfig -a [-m] [-d] [-u] [protocol_family] ifconfig -l [-d] [-u]
DESCRIPTION
ifconfig is used to assign an address to a network interface and/or con- figure network interface parameters. ifconfig must be used at boot time to define the network address of each interface present on a machine; it may also be used at a later time to redefine an interface's address or other operating parameters. Available operands for ifconfig: Address For the DARPA-Internet family, the address is either a host name present in the host name data base, hosts(5), or a DARPA Inter- net address expressed in the Internet standard ``dot notation''. For the Xerox Network Systems(tm) family, addresses are net:a.b.c.d.e.f, where net is the assigned network number (in decimal), and each of the six bytes of the host number, a through f, are specified in hexadecimal. The host number may be omitted on 10Mb/s Ethernet interfaces, which use the hardware physical address, and on interfaces other than the first. For the ISO family, addresses are specified as a long hexadecimal string, as in the Xerox family. However, two consecutive dots imply a zero byte, and the dots are optional, if the user wishes to (careful- ly) count out long strings of digits in network byte order. address_family Specifies the address family which affects interpretation of the remaining parameters. Since an interface can receive transmis- sions in differing protocols with different naming schemes, spec- ifying the address family is recommended. The address or proto- col families currently supported are ``inet'', ``atalk'', ``iso'', and ``ns''. Interface The interface parameter is a string of the form ``name unit'', for example, ``en0'' The following parameters may be set with ifconfig: alias Establish an additional network address for this inter- face. This is sometimes useful when changing network numbers, and one wishes to accept packets addressed to the old interface. arp Enable the use of the Address Resolution Protocol in map- ping between network level addresses and link level ad- dresses (default). This is currently implemented for mapping between DARPA Internet addresses and 10Mb/s Eth- ernet addresses. -arp Disable the use of the Address Resolution Protocol. broadcast mask (Inet only) Specify the address to use to represent broadcasts to the network. The default broadcast address is the address with a host part of all 1's. debug Enable driver dependent debugging code; usually, this turns on extra console error logging. -debug Disable driver dependent debugging code. delete Remove the network address specified. This would be used if you incorrectly specified an alias, or it was no longer needed. If you have incorrectly set an NS address having the side effect of specifying the host portion, removing all NS addresses will allow you to respecify the host portion. dest_address Specify the address of the correspondent on the other end of a point to point link. down Mark an interface ``down''. When an interface is marked ``down'', the system will not attempt to transmit mes- sages through that interface. If possible, the interface will be reset to disable reception as well. This action does not automatically disable routes using the inter- face. ipdst This is used to specify an Internet host who is willing to receive ip packets encapsulating NS packets bound for a remote network. An apparent point to point link is constructed, and the address specified will be taken as the NS address and network of the destination. IP encap- sulation of CLNP packets is done differently. media type Set the media type of the interface to type. Some inter- faces support the mutually exclusive use of one of sever- al different physical media connectors. For example, a 10Mb/s Ethernet interface might support the use of either AUI or twisted pair connectors. Setting the media type to ``10base5/AUI'' would change the currently active con- nector to the AUI port. Setting it to ``10baseT/UTP'' would activate twisted pair. Refer to the interfaces' driver specific man page for a complete list of the available types. mediaopt opts Set the specified media options on the interface. opts is a comma delimited list of options to apply to the in- terface. Refer to the interfaces' driver specific man page for a complete list of available options. -mediaopt opts Disable the specified media options on the interface. metric n Set the routing metric of the interface to n, default 0. The routing metric is used by the routing protocol (routed(8)). Higher metrics have the effect of making a route less favorable; metrics are counted as addition hops to the destination network or host. mtu n Set the maximum transmission unit of the interface to n. Most interfaces don't support this option. netmask mask (Inet and ISO) Specify how much of the address to reserve for subdividing networks into sub-networks. The mask in- cludes the network part of the local address and the sub- net part, which is taken from the host field of the ad- dress. The mask can be specified as a single hexadecimal number with a leading 0x, with a dot-notation Internet address, or with a pseudo-network name listed in the net- work table networks(5). The mask contains 1's for the bit positions in the 32-bit address which are to be used for the network and subnet parts, and 0's for the host part. The mask should contain at least the standard net- work portion, and the subnet field should be contiguous with the network portion. nsellength n (ISO only) This specifies a trailing number of bytes for a received NSAP used for local identification, the re- maining leading part of which is taken to be the NET (Network Entity Title). The default value is 1, which is conformant to US GOSIP. When an ISO address is set in an ifconfig command, it is really the NSAP which is being specified. For example, in US GOSIP, 20 hex digits should be specified in the ISO NSAP to be assigned to the interface. There is some evidence that a number differ- ent from 1 may be useful for AFI 37 type addresses. trailers Request the use of a ``trailer'' link level encapsulation when sending (default). If a network interface supports trailers, the system will, when possible, encapsulate outgoing messages in a manner which minimizes the number of memory to memory copy operations performed by the re- ceiver. On networks that support the Address Resolution Protocol (see arp(4); currently, only 10 Mb/s Ethernet), this flag indicates that the system should request that other systems use trailers when sending to this host. Similarly, trailer encapsulations will be sent to other hosts that have made such requests. Currently used by Internet protocols only. -trailers Disable the use of a ``trailer'' link level encapsula- tion. link[0-2] Enable special processing of the link level of the inter- face. These three options are interface specific in ac- tual effect, however, they are in general used to select special modes of operation. An example of this is to en- able SLIP compression, or to select the connector type for some ethernet cards. Refer to the man page for the specific driver for more information. -link[0-2] Disable special processing at the link level with the specified interface. up Mark an interface ``up''. This may be used to enable an interface after an ``ifconfig down.'' It happens auto- matically when setting the first address on an interface. If the interface was reset when previously marked down, the hardware will be re-initialized. ifconfig displays the current configuration for a network interface when no optional parameters are supplied. If a protocol family is specified, Ifconfig will report only the details specific to that protocol family. If the -m flag is passed before an interface name, ifconfig will display all of the supported media for the specified interface. Optionally, the -a flag may be used instead of an interface name. This flag instructs ifconfig to display information about all interfaces in the system. -d limits this to interfaces that are down, and -u limits this to interfaces that are up. The -l flag may be used to list all available interfaces on the system, with no other additional information. Use of this flag is mutually ex- clusive with all other flags and commands, except for -d (only list in- terfaces that are down) and -u (only list interfaces that are up). Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exit, the requested address is unknown, or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
netstat(1), netintro(4), rc(8), routed(8),
HISTORY
The ifconfig command appeared in 4.2BSD. 4.2 Berkeley Distribution April 16, 1997 4
Powered by man-cgi (2024-08-26). Maintained for NetBSD by Kimmo Suominen. Based on man-cgi by Panagiotis Christias.